X-PROGRAM X-A10 Скачать руководство пользователя страница 14

Specifications

We follow a policy of continuous advancement in
development.
For this reason all or part of specifications & designs
may be changed without prior notice.

14

X-program

X-A10

X-A20

Number of channels

1

2

Amplifier class

AB

AB

Power output, 4 ohm (0,1% THD)

200 W

2 x 50 W

Power output, 2 ohm (0,2% THD)

300 W

2 x 70 W

Power output, 4 ohm bridged

N/A

1 x 140 W

Signal to noise ratio, A-weighted

>90 dB

>90 dB

Damping factor

>80

>80

Frequency response

20 Hz - 30 kHz

20 Hz - 30 kHz

Input impedance, low level

22 kohm

22 kohm

Input impedance, high level

220 ohm

220 ohm

High level input with auto start

Yes

Yes

Parallel input switch

-

-

Input sensitivity

0,25 - 5V

0,25 - 5V

Filter subsonic @ 25 Hz

Yes

Yes

Filter high-pass

Off / 70 / 90 Hz

Off / 70 / 90 Hz

Filter low pass variable

50-250 Hz*

50-200 Hz *

* can be switched in/out

(18 dB/oct)

Built-in fan cooling

Yes

-

Power consumption, idle

0,8 A

0,4 A

Power consumption, max

65A

35A

Fuse

2 x 25 A

1 x 25 A

Dimensions HxWxD(mm)

72 x 255 x 358

72 x 255 x 278

Dimensions (inch)

2,8 x 10 x 14

2,8 x 10 x 10,9

Weight

3 kg

2,3 kg

X-program

X-A30

X-A40

Number of channels

3

4

Amplifier class

AB

AB

Power output, 4 ohm (0,1% THD)

2 x 50 W

4 x 50 W

Power output, 2 ohm (0,2% THD)

2 x 70 W

4 x 70 W

Power output, 4 ohm bridged

1 x 140 W

2 x 140 W

Power out mono sub ch. 4 ohm

1 x 120 W

N/A

Power out mono sub ch. 2 ohm

1 x 180 W

N/A

Signal to noise ratio, A-weighted

>90 dB

>90 dB

Damping factor

>80

>80

Frequency response

20 Hz - 30 kHz

20 Hz - 30 kHz

Input impedance, low level

22 kohm

22 kohm

Input impedance, high level

220 ohm

220 ohm

High level input with auto start

Yes

Yes

Input sensitivity

0,25 - 5V

0,25 - 5V

Filter high pass, front channels

Off / 70 / 90 Hz

Off / 70 / 90 Hz

Filter low pass, rear channels

50 - 100 Hz*

Filter low pass Sub channel

50 - 100 Hz

Filter subsonic @ 25 Hz

Yes, on all channels Yes, on all channels

* can be switched in/out

Power consumption, idle

0,7 A

0,5 A

Power consumption, max

50 A

50 A

Fuse

2 x 25 A

2 x 20 A

Dimensions HxWxD(mm)

72 x 255 x 378

72 x 255 x 398

Dimensions (inch)

2,8 x 10 x14,9

2,8 x 10 x 15,7

Weight

3,2 kg

3,5 kg

All above output power
ratings at 14,4 VDC

Содержание X-A10

















Отзывы: