4K UHD HDCP 2.2 HDBaseT Extender Set with 2-way PoH,
IR and RS-232 (4K: 35m/114ft | 1080p: 70m/230ft)
EX-35-H2
Quickstart Guide
In the Box
1x EX-35-H2 Transmitter
1x EX-35-H2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
2x 3-pin Screw Down Phoenix Connectors
2x Wide-band IR Emitters
2x Wide-band IR Receivers (30-50KHz)
4x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI Display
HDMI
HDMI
IR Emitter
IR Emitter
IR Receiver
18V DC 1A
Power Supply
or
IR to Control System
CAB-IR-LINK (Sold Separately)
EX-35-H2 Transmitter (TX)
EX-35-H2 Receiver (RX)
4K/UHD HDMI Source
KEY
HDMI
HDBaseT Cat5e/6/6a
IR TX and RX
Power
HDBaseT
Cat5e/6/6a/7
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI, or HDBaseT connections
while the transmitter or receiver is powered on. Doing so may cause damage
to the units or connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Refer to the Installation Guide and other documentation on the
product page for additional information.
Installation
Before Beginning
• Verify that all items are included in the packaging per the
list.
Pre Wire
1.
Run a Cat5e/6/6a cable from the transmitter location to the receiver
location. Terminate the cable per the
2.
(Optional) If using 3
rd
party IR emitters or connecting blocks at either the
transmitter or receiver, run the wire and terminate per the
3.
(Optional) If using RS-232 pass-through, run the wire and terminate per
the
4.
(Optional) If using 3rd party IR receivers at either the transmitter or
receiver, run the wire and terminate per the
section.
Transmitter Installation
1.
Connect an HDMI source to the
HDMI In
on the transmitter using an
HDMI cable from a high quality brand such as
2.
(Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the
IR TX
port.
3.
Connect the cable created in
HDBT Out
.
4.
(Optional) Connect the 3-pin connector to the
RS-232
port on the
transmitter and the opposite end to a port on a control system.
5.
If using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the
18V DC 1A
jack.
Receiver Installation
1.
Connect the
HDMI Out
on the receiver to an input on the display using
an HDMI cable from a high quality brand such as
2.
(Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the
IR TX
port.
3.
Connect the cable created in
HDBT In
.
4.
(Optional) If using RS-232 pass-through, connect the 3-pin connector
to the
RS-232
port on the receiver and the opposite end to a port on the
device being controlled.
5.
If not using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the
18V DC 1A
jack.
Copyright © 2016 WyreStorm Technologies |
EX-35-H2 Quickstart Guide | 161102
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
