Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit repair,
component replacement or complete product replacement in the event of malfunction. The decision to repair or replace will
be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal
wear and tear or cosmetic damage. Visit the product page located at
for additional information on this
product including important technical information not provided in this document and warranty terms & conditions.
Specifications
Copyright © 2016 WyreStorm Technologies |
EX-35-H2 Quickstart Guide | 161102
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiving device
and that both devices are powered on.
Note:
When using PoH, to power the receiver, verify that the HDBaseT cable is
properly terminated per the
section.
• Verify that the transmitter, receiving device, and display support the output
resolution of the source. Refer to
Video Resolutions
table for the max distance based on resolution.
• Verify that the receiving device and display support the output resolution of
the source.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
• Verify that the HDBaseT cable is properly terminated per the
section.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3
rd
party Device Control
• Verify that the IR cable(s) is properly terminated. See
.
• Verify that the IR emitter is located near the IR receiver on the device.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
• Use a flashlight to locate the IR receiver behind any tinted panels on the
device being control.
Power
Power Supply
Input: 100~240V AC 50/60Hz |
Output: 18V DC 1A
Max Power Consumption
8.88W
PoH
2-way: 48V 15.4W
Environmental
Operating Temperature
32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature
-4°F ~ 158°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Maximum BTU
30.30 BTU/hr
Dimensions and Weight
Rack Units/Wall Box
1U
Height
17mm/0.67in
Width
140mm/5.52in
Depth
90.2mm/3.56in
Weight (Each Unit)
0.36kg/0.79lbs
Regulatory
Safety and Emission
CE
Audio and Video
Inputs
Transmitter:
1x HDMI 19-pin type A |
Receiver:
1x HDBaseT 8-pin RJ-45 female
Outputs
Transmitter: 1x HDBaseT 8-pin RJ-45 female | Receiver: 1x HDMI 19-pin type A
Audio Formats
2ch PCM | Up to DTS-X and Dolby Atmos
Video Resolutions (Max)
HDMI
1920x1080p @60Hz 12bit (15m/50ft) | 16bit (7m/23ft)
3840x2160p @30Hz 4:4:4 8bit (7m/23ft) | @24Hz 4:2:0 HDR 10bit (3m/9.8ft)
4096x2160p @60Hz 8bit 4:2:0 (7m/23ft) | @60Hz 8bit 4:4:4 (7m/23ft)
Cat6
1920x1080 @60Hz 12bit (70m/230ft) | @60Hz 16bit (35m/115ft)
3840x2160p @30Hz 4:4:4 8bit (35m/115ft) | @24Hz 4:2:0 HDR 10bit (35m/115ft)
4096x2160p @60Hz 4:2:0 8bit (35m/115ft)
Cat6a/7
1920x1080 @60Hz 12bit (70m/230ft)
3840x2160p @30Hz 4:4:4 8bit (70m/230ft) | @24Hz 4:2:0 HDR 10bit (70m/230ft)
4096x2160p @60Hz 4:2:0 8bit (70m/230ft)
Color Depth
1080p: 12bit | 4K UHD: 8bit | HDR @24p: 10bit per channel BT.2020
Maximum Pixel Clock
297MHz
Communication and Control
HDMI
HDMI 2.0 | HDCP 2.2 | EDID | CEC Pass-through | DVI/D supported with adapter (not included)
HDBaseT
HDMI 2.0 | HDCP 2.2 | EDID | 2-way PoH | Bidirectional IR and RS-232
IR
1x IR TX 3.5mm (1/8in) Mono | Bidirectional over HDBaseT | 1x IR RX 3.5mm (1/8in) Stereo | Bidirectional over HDBaseT
RS-232
1x 3-pin Screw Down Phoenix Connector | Bidirectional over HDBaseT
