manualshive.com logo in svg

Wurtec S3 Communicator, Инструкция по эксплуатации

Поделиться
Скачать
Wurtec S3 Communicator Скачать руководство пользователя страница 19

 

 

19 

 

ii.

 

If at some point the Command Center was placed on speaker without 
returning the handset back to the receiver, both may not function 
properly and you will need to ensure phone is on hook by returning 
handset to receiver and turning off speakerphone.  

 

TECHNICAL SUPPORT 

Tech support can be reached at (419) 930-1066 or toll free at (800) 837-1066, Monday through Friday, 
8:00 a.m. to 5:00 p.m. EST> 

 

DAILY CHECKS 

The Command Center is intended to be self-sufficient, so minimal maintenance is required to keep it 
in operating condition. The Command Center will display any warning messages or error conditions 
that are detected until acknowledged, so it should be checked at a minimum of once per day. 
 

MAINTENANCE 

The Command Center battery is the only component that will require regular maintenance and should 
be replaced at least once every 5 years. 

 

CERTIFICATES AND COMPLIANCE 

FCC Part 15, Class A 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference, in which case 
the user will be required to correct the interference at his own expense. 

Содержание S3 Communicator




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды