Wright Velke V-TURN, Руководство пользователя

Страница: 7 / 22

•
Start the engin run at low
RPM for se Release the
parking brake. Now gradually close the manual bypass valves on top of each pump one at a time,
and see if the wheels start to move. If the wheels move when the hand controls are in neutral
pos ion, a
nt allen screw located on each pump until they stop. The
uld now b ontrol
d. Che
s. If no wheels
ral o plied.
e parking brake locking system
while engaged. If not, service the parking brake locking syste .
•
Before testing the blade clu ng
vulnerable to possible th the mower
de discharge at this or at any time. The discharge chute deflector should be in
the down brake should now Move the engine throttle to ¾ speed
minute or so. Try engaging and disengaging the
If the blades do n seconds
With
sw es
rvice th
t o
lot. It is r
furt
nt.) Check that the m
controls are held to the full speed position which
n trac
oise
afety in
r. Instruct the customer
lo
sic operation and use of t
tion
e according to the engine manufacturer’s recommendation. Let the engine
veral minutes to get the hydraulic fluid circulating through the pumps, etc.
it djust the neutral adjustme
manual valves on top of each pump sho
levers, one at a time, forward and backwar
backward according to position of the lever
stop when the hand controls are in the neut
Now check if th e firmly closed. Now try moving the hand c
ck to see if the wheels move forward and
t, service the hand control system. If the
sition the parking brake should now be ap p
(if applicable) prevents the unit from being driven
m
tch/brake operation, make sure the area is clear and there is nothi
rown objects from under the mower. No one should be near
ck or in its line of
position. The parking be applied.
setting.
•
Turn on the blade clutch switch. Run blades for a
blades a few times about 10 seconds apart.
each time, service the blade brake system.
switch to test the Operator Presence Control
should stop in several seconds. If not, se
•
Disengage the blades, set the parking brake, shu
stand(s).
•
Drive the mower around on a level parking
Speed/Sensitivity Adjustment be used. (See
Speed/Sensitivity Adjustme
ot start and stop in a few
the blades on, now try disengaging the OPC
itch (OPC). The engine should die and the blad
e OPC system. Try this a couple of times.
ff the engine and remove the mower from the
ecommended that the slower setting of the
her in this manual for information on
ower drives in a straight line when both hand
is up against the stationary control bar. If not,
king adjustment.
s and test for irregular operation and adjust or
formation and operating procedures in this
in proper operation and observe the customer
t. Make sure the customer is familiar and
he mower.
see further in this manual for information o
•
As you drive the mower, listen for any unusual n
service as necessary. Next, go over the s
manual with the custome
during their initial operation on a level parking
comfortable with the ba
•
Dealer: Please fill out and follow the instruc on the Product Registration Form and have
tomer fill out his part of the form. Afte the Product Registration Card is filled out
senta ive from your dealership, please mail or fax it
your Wright Commercial
rections
eep y
ucts
the
and ou
y for
the cus r
and signed by the customer and a repre
immediately (within 14 days from date of retail purchase) to t
Products Distributor according to the di
copy of the registration form and then k on the Card. Then give the customer his
our copy and mail the remaining copies of the
Distributor. The limited warranty is not valid
above steps are taken. Remember, the
his satisfaction is very important. Thank y
delivery to your customer.
form to your Wright Manufacturing Prod
unless the mower is registered and all of
purchaser is both your and our customer
for supporting our products.
•
The mower is now read
2