background image

enclosed area without good, approved 
ventilation. Exhaust fumes are dangerous. 

 

ition, even 

 Wh

nt 

ing lots 

ss, turn off the 

 Bef

wire 

 

tops from 

excessive speeds may cause serious injury.

 

 The grass discharge chute deflector must be 

e down 

hen 

alled. 

 If the mower discharge clogs, turn off the blade 

 

 blade 

rear wheels, 

blades, engine flywheel, belts and pulleys. 

 

aves and lubricant spills from 

surfaces after use to prevent fire hazard. 

 Be alert for traffic when crossing roads or 

operating ne

 Before crossing 

walks or 

roads,

t for them 

 

se 

rp turns to 

revent tipping or loss of control. Be especially 

autious when changing direction on slopes. 

he Wright mower is capable of greater traction 

n slopes than typical riding mowers because of 

e be

 

 
 
 

 
 

Initial Operating Safety Guidelines: 

 Read and understand the warning on the 

instrument panel of the mower. 

 Keep a firm hold on the stationary handle at all 

times. 

 Know the controls and how to stop quickly.

 

 Before attempting to start the engine, follow all

starting instructions below and in the engine 
operator’s manual. 

 Look behind before backing up and use 

extreme caution when backing up while 
standing on the Velke. 

 Before leaving the operator’s pos

momentarily, turn off the blade clutch 
engagement switch and apply the parking 
brake. Keep others from coming near the 
mower. Return to the operator position as 
soon as possible. 

en leaving the Wright mower unattended, 

turn off the blade clutch engageme
switch, apply the parking brake, stop the 
engine and remove the key. Never leave 
the machine unattended on a slope. If the 
parking brake becomes disengaged, the 
mower could roll which would be 
hazardous. 

 When transporting, driving onto transport 

vehicles, into buildings, across park
or otherwise not mowing gra
blade clutch engagement switch to reduce 
risk of thrown objects and rotating blade 
hazard. After coming to a stop, apply the 
parking brake, stop the engine and remove 
the key. 

ore performing any maintenance or repair 

service, mowing height or other 
adjustments, disengage power to blades, 
apply the parking brake, stop the engine, 
remove ignition key and spark plug 
from spark plug(s). 

 DO NOT allow inexperienced people to operate

the mower until they have read and 
understood these safety instructions. 
Operate the mower at slower speeds while 
becoming familiar with it. 

 Speeding is dangerous for even an 

experienced operator. Sudden s

installed at all times and in th
position except that it may be raised w
the grass catcher is completely inst

clutch switch, apply the parking brakes, 
stop the engine and remove the key before
removing obstruction. 

 Keep all shields and covers in place, especially 

grass discharge chute deflector, the
belt cover, and the pump belt/pulley cover. 

 Keep hands, feet and clothing away from 

rotating parts, especially the 

 Do not touc

 engine is

running or soon after it is stopped. These 
areas can be so hot as to cause severe 
burns. 

 Clean grass, le

h engine or muffler while

ar roadways. 

gravel drives, side

 turn off the blades and wai

to stop

 
 
 
 
 

Operation on Slopes: 

DO NOT operate on steep slopes. Do not 
operate the mower on slopes steeper than you 
can feel secure about the traction of the tires an
the stability of the mower. Do not operate the 
mower on slopes at all when the grass is wet. 
There is a danger of suddenly sliding sideways or
down the hill. When operating on a slope, travel 
across the grade whenever possible, not in an u
or down pattern. Reduce speed and exerci

xtreme caution on slopes and in sha

e
p
c
 
T
o
th

nefits of a lower center of gravity. It is 

tial for you to know more about the 

essen
handling characteristics of the mower so that you

     

WARNING

 

     

WARNING

 

 

Содержание V-TURN























Отзывы: