background image

37 

 

Wright

  Manufacturing,  Inc.  (hereinafter:  WMI)  warrants  to  the  original 

owner  that  the  new  WMI  mower  accompanying  this  document  will  be 

free from manufacturing defects in materials or workmanship subject to 

the following limitations and exclusions.  Any part of the WMI commercial 

mower manufactured by WMI and found, in the reasonable judgment of 

WMI,  to  be  defective  in  materials  or  workmanship,  will  be  repaired  or 

replaced by an Authorized WMI Service Dealer without charge for parts 

and (except as excluded below) labor.  This Warranty is limited to the 

original Owner and the mower this document was provided with and is 

not transferable.  Dealer demo units with less than fifty hours when first 

retailed  shall  also  be  covered  by  this  limited  warranty.    Proofs  of 

Purchase,  Authorized  Dealer  performed  Pre-Deliver  Service  and  the 

First Eight Hour Service will be required by the Authorized WMI Service 

Dealer to substantiate any warranty claims.  All WMI warranty work must 

be performed by an Authorized WMI Service Dealer and item must be 

delivered to the dealer prior to the expiration of the warranty period.  This 

Warranty is limited to the following specified periods from the date of the 

original retail purchase for defects in materials or workmanship and will 

commence upon the date of original retail purchase.  This warranty shall 

apply  only  if  the  warranty  registration  form  has  been  completed  and 

returned to Wright Manufacturing, Inc. within 14 days from the date of 

original retail purchase. This warranty includes only the cost of parts and 

labor (when applicable).  This warranty applies only to the replacement 

of  defective  or  otherwise  warrantable  WMI  OEM  parts  being  replaced 

with WMI OEM parts.

 

 

 

  All  parts  and  components  (except  as  noted  below)  –  2 

years  

 

 Belts – 90 days  

 

 Battery – 90 days 

 

 Engine – warranty covered by engine manufacturer and handled 

  through the respective Authorized engine Dealers 

 

Exclusions:

 

Any damage or deterioration due to normal use, wear and tear or 

exposure 

All filters, engine oil, hydraulic oil, tires and tubes 

Bent, fractured or broken parts occurring through impact or hard use 

Clutch: linings, anti-rotation failure or other failure due to improper 

replacement installation 

Cost of regular maintenance service, parts or adjustments 

Worn bearings (other than spindle bearings; see above) 

Worn bushings, cotters, clips, pins and retainers 

Grease fittings/zerks 

Paint, paint fading, cosmetic imperfections and steel surface 

imperfections 

Fabric, cushion and rubber grip wear or damage 

Cutting blades, light bulbs, fuses 

Damage due to loose pulleys on shafts 

Damage due to loose wheel hubs on tapered hydraulic motor shafts 

Fire Damage 

Abrasion or corrosion wear or damage 

 

Repair Parts Replaced During Original Warranty 

All Repair parts (excluding wear or otherwise excluded 

items) installed during the warranty period are warranted 

until the end of the respective original period according to 

the categories above except in the case that the respective 

original warranty period expires in less than ninety (90) 

days after the installation of the part(s).  If this happens 

then the parts are warranted for a total of ninety (90) days 

from the time of their installation. 

 

Rental Use 

The above warranty periods are limited to maximum of 
ninety (90) days for mowers that are used for rental 
purposes. 

 

 

 

The WMI mower, including any defective part, must be returned to an  

Authorized WMI Service Dealer within the warranty period.  The expense of 

lost  production  time  and  delivering  the  mower  to  the  Authorized  WMI 

Service  Dealer  for  warranty  work  and  the  expense  of  returning  it  to  the 

Owner after repair will be paid for by the Owner.  WMI’s responsibility is 

limited to making the required repairs and no claim of breach of warranty 

shall be cause for cancellation or rescission of the contract of sale of any 

WMI  mower.    This  Warranty  does  not  apply  to  any  mower  that  was 

delivered to an Owner prior to the Pre-Delivery Service as specified in the 

Owner’s  Manual.    This  Warranty  does  not  apply  to  any  mower  that  was 

shipped  in  a  crate  to  the  Owner  or  delivered  to  the  Owner  by  non-

employees of an Authorized Dealer.  For the Owner’s protection and a valid 

Warranty, please note:  WMI does not permit Authorized Dealers to make 

non-face-to-face deliveries of the mower and any who are found doing so 

are  subject  to  immediate  cancellation  as  Authorized  Dealers.    This 

Warranty  does  not  cover  any  mower  that  has  been  subject  to  misuse, 

neglect,  negligence,  burning  in  any  fire,  an  accident,  or  that  has  been 

operated  or  maintained  in  any  way  contrary  to  the  operating  and 

maintenance  instructions  as  specified  in  the  Owner’s  Manual.    The 

Warranty does not apply to any damage to the mower that is the result of 

improper  maintenance  or  to  any  mower  or  parts  that  have  not  been 

assembled or installed as specified in the Owner’s Manual.  The Warranty 

does  not  cover  any  mower  that  has  been  altered  or  modified  changing 

performance  or  durability.    In  addition,  the  Warranty  does  not  extend  to 

repairs  made  necessary  by  normal  wear,  or  by  the  use  of  parts  or 

accessories  which,  in  the  reasonable  judgment  of  WMI,  are  either 

incompatible  with  the  WMI  mower  or  adversely  affect  its  operation, 

performance or durability. 

 

WMI  reserves  the  right  to  change  or  improve  the  design  of  any  mower 

without  assuming  any  obligation  to  modify  any  mower  previously 

manufactured. 

 

All  other  implied  warranties  are  limited  in  duration  to  the  two  (2)  year 

warranty period or ninety (90) days for mowers used for rental purposes.  

Accordingly, any such implied warranties including merchantability, fitness 

for a particular purpose, or otherwise, are disclaimed in their entirety after 

the expiration for the appropriate two (2) year or ninety (90) day warranty 

period.  WMI’s obligation under this Warranty is strictly limited to the repair 

or replacement of defective parts and WMI does not assume, or authorize 

anyone to assume for them, any other obligation.  Some states do not allow 

limitations on how long an implied warranty lasts, so the above limitation 

may not apply. 

 

WMI  assumes  no  responsibility  for  incidental,  consequential  or  other 

damages  including,  but  not  limited  to,  expense  for  gasoline,  expense  of 

delivering the mower to an Authorized WMI Service Dealer and expense of 

returning it to the Owner, damage by fire, mechanic’s travel time, telephone 

charges, rental of a like product during the time warranty repairs are being 

performed,  travel,  loss  or  damage  to  personal  property, loss  of  revenue, 

loss of use of the power equipment, loss of time or inconvenience.  Some 

states do not allow the exclusion or limitation of incidental or consequential 

damages, so the above limitation or exclusion may not apply. 

 

This Warranty gives you specific legal rights, and you may also have other 

rights which vary from state to state. 

 

This  Warranty  applies  to  all  WMI  mowers  sold  in  the  United  States  of 

America and Canada. 

 

For  the  location  of  the  Authorized  WMI 
Service  Dealer  nearest  you  or  other 
information,  such  as,  Parts  Lists  and 
Owner’s  Manuals  visit  our  website  at: 

www.wrightmfg.com

  

 

Wright Manufacturing, Inc. 

4600-X Wedgewood Blvd. 

Frederick, MD 21703 

WRIGHT MANUFACTURING, INC. POWER EQUIPMENT LIMITED WARRANTY 

THIS WARRANTY SUPERSEDES ALL PREVIOUS ON UNITS WITH A RETAIL SALES DATE ON OR AFTER 04/01/05 

Содержание HYDRO PISTOL GRIP













































Отзывы: