background image

 

TST-019 MRTALPCH CHANNEL 

– Rev. 2016-310 

Page 16 of 20 

 

6)  Vacuum line sections and included fittings may be tested by moving up each line (toward the 

vacuum generating system) to the next fitting, removing the hose and plugging it at the fitting, 
or by installing the ball valve assembly (with the gauge end toward

s the section that the lifter’s 

gauge has been separated from) into the line. 

7)  Each circuit (red and green) has one vacuum pad connected by a quick connect, shown in 

FIGURE 22 

below.  Disconnect the quick connect and repeat the vacuum test. 

 

If, with the quick connect disconnected, the vacuum level, as shown on the lifter’s vacuum 
gauge, still indicates a leak (vacuum level drops), proceed to step 10. 

 

If, with the quick connect disconnected, the vacuum level, as shown on the lifter’s vacuum 
gauge, now holds steady and does not leak, the indication is that the leak is located in the 
section that was removed.  This would be the pad fitting, hose, the quick connect plug 
assembly, or that the quick connect leaks when connected.  Proceed as follows. 

8)  Remove the hose from the barbed fitting of 

the male quick connect plug and cap off the 
barbed fitting.  Connect the male plug to the 
female quick connect coupler. See 

FIGURE 23

Repeat the vacuum test. 

  If the leak resumes, examine the threads 

of the barbed fitting for indication of 
cracks.  If the fitting itself does not appear 
damaged, replace the quick connect.  
Note, the O-ring that seals the male 
portion of the quick connect to the female 
half when they are attached is part of the 
female coupler, due to this it is recommended that both the male and female quick connect 
be replaced. 

  If the vacuum level, 

as shown on the lifter’s vacuum gauge, continues to hold steady and 

does not drop, the indication is that the quick connect does not leak when connected.  
Continue to next step. 

FIGURE 22 

 

FIGURE 23 

 

Содержание MRTALPCH611LDC
























Отзывы: