background image

#35202AFT

Rev 3.1/9-22

8

LIMITED WARRANTY

Wood's Powr-Grip

®

 (WPG) products are carefully constructed, thoroughly inspected at various 

stages of production, and individually tested. They are warranted to be free from defects in 
workmanship and materials for a period of one year from the date of purchase.

If a problem develops during the warranty period, follow the instructions below to obtain 
warranty service. If inspection shows that the problem is due to defective workmanship or 
materials, WPG will repair the product without charge.

Warranty does not apply when ...

•   modifications have been made to the product after leaving the factory

•   rubber portions have been cut or scratched during use;

•   repairs are required due to abnormal wear and tear, and/or;

•   the product has been damaged, misused or neglected.

If a problem is not covered under warranty, WPG will notify the customer of costs prior to 
repair. If the customer agrees to pay all repair costs and to receive the repaired product on a 
C.O.D. basis, then WPG will proceed with repairs.

T

O

 O

BTAIN

 R

EPAIRS

 

OR

 W

ARRANTY

 S

ERVICE

For purchases in 

North America

:

Contact the WPG Technical Service Department. When factory service is required, ship the 
complete product – prepaid – along with your name, address and phone number to the street 
address listed at the bottom of this page.  WPG may be reached by phone or fax numbers listed 
below.

For purchases in all 

other localities

:

Contact your dealer or the WPG Technical Service Department for assistance.  WPG may be 
reached by phone or fax numbers listed below.

Wood's Powr-Grip Co., Inc.

908 West Main St.

Laurel, MT 59044 USA

406-628-8231 (phone)

800-548-7341 (phone)

406-628-8354 (fax)

Содержание 95723











Отзывы: