Wow SparkMaker SLA Скачать руководство пользователя страница 4

Страница: 4 / 58

©This is a desktop-grade SLA light-cured 3D printer that delivers high-quality, light-cured 3D

printing experience when the power supply is working properly and components are not damaged.

©Read the entire user manual and become familiar with the features of the product before

proceeding. Failure to operate this product properly may result in serious injury to yourself or

others, or damage to the product or property damage. This product is more complex and requires

a period of familiarity before it can be used safely and requires some expertise to operate. Without

a strong sense of safety, improper safety practices can result in product damage and property

damage, and can even cause serious harm to others. This product is not suitable for children. Do

not use parts that are not provided or recommended by

WOW,

and must be installed and used in

strict accordance with wow guidelines. This guidance document contains instructions for safety,

operation, and maintenance. Be sure to visit the

SparkMaker

website (https://www.sparkmaker3d.

com/) to download the user manual and read all instructions and warnings in the documentation

before proceeding with assembly setup and use.

©Please read this document carefully before using the product to understand your legal rights,

responsibilities and safety instructions; otherwise it may cause property damage, safety accidents and

personal safety hazards. By using this product, you are deemed to have understood, endorsed and

accepted all the terms and contents of this document. The user is committed to being responsible

for his or her actions and all consequences arising therefrom. The user undertakes to use the product

only for legitimate purposes and agrees to all terms and content of this document and any relevant

policies or guidelines that may be customized by WOW Innovations (Shenzhen) Technology Co., Ltd.

©WOW Innovation (Shenzhen) Technology Co., Ltd. reserves the right to update this Disclaimer and

Warning. WOW Innovation (Shenzhen) Technology Co., Ltd. does not assume any loss caused by

the user not using the product in this User Manual. In compliance with laws and regulations, WOW

Innovation (Shenzhen) Technology Co., Ltd. has the final right to interpret this document. WOW

Innovation (Shenzhen) Technology Co., Ltd. reserves the right to update, change or terminate these

Terms without prior notice.

Disclaimer and warning

Содержание SparkMaker SLA


























































Результаты поиска

Содержание SparkMaker SLA

Отзывы:

Бренды по названию

Популярные бренды

Wow SparkMaker SLA, Руководство по эксплуатации

Результаты поиска

Содержание SparkMaker SLA

Отзывы:

Бренды по названию

Популярные бренды