16
Cordless Lawn mower
EN
to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut
perpendicular (across) the first cut pattern. DO
NOT CHANGE CUT PATTERN IN ANY WAY THAT
WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week.
This will help prevent matting and graining of the
lawn.
CUTTING AREA
The cutting area can be affected by several factors,
such as cutting height, lawn humidity, grass length
and density. Besides, starting and stopping the
mower too many times during operation will reduce
the cutting area.
The table below gives the relationship between
cutting conditions and cutting area.
Cutting Height
Cutting Area (maximum)
Cut 8cm to 6cm
460m
2
*
* Used with two fully charged battery packs.
TIPS:
1) It is recommended to mow your lawn more frequently,
walk at normal pace, and not to start/stop the mower
too often during operation.
2) For best performance, please ensure use two fully
charged battery packs at the same time and always cut
off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as to have
more effective cutting and properly discharge the
clippings.
4) Avoid cutting wet grass, otherwise it will stick to the
underside of the deck and the clippings cannot be
collected or discharged properly.
5) A higher cutting height shall be applied to new or thick
grass and it will extend the battery duration.
MAINTENANCE
WARNING:
Stop the mower and remove the safety
key before removing the grass collection bag.
Note:
To ensure long and reliable service, perform the fol-
lowing maintenance procedures regularly. Check for obvious
defects such as a loose, dislodged or a damaged blade,
loose fittings, and worn or damaged components. Check that
the covers and guards are all undamaged and are correctly
attached to mower. Carry out any necessary maintenance
or repairs before operating mower. If the mower should
happen to fail despite regular maintenance, please call our
customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING,
SHARPENING, AND INSTALLING BLADE. ENSURE THAT
SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand causes
the blade to dull quickly. If your lawn has sandy soil, more
frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. L)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep it bal-
anced, removing equal amounts of material from both ends.
Note:
1. Be sure the mower is turned off and remove the key.
2. Place the mower in stand up storage mode.
BLADE BALANCING (See Fig. M)
Check balance of blade by placing center hole in blade M-1
over a nail or screwdriver shank M-2, clamped horizontally in
a vise M-3. If either end of the blade rotates downward, file
that end. Blade is properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. N1, N2)
Replace your metal Blade after 50 hours mowing or 2 years,
which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the Blade.
You will need garden gloves (not provided) and a spanner
wrench (not provided) to remove the Blade. Hold the Blade
and unscrew the Blade Bolt counter-clockwise using a span-
ner wrench, and then remove the Blade.
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
STORAGE (See Fig. K1,K 2)
Stop the mower and always remove the Safety Key.
Clean the exterior of the machine thoroughly using
a soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially from
the ventilation slots.
Turn the machine on its side and clean the blade area.
If grass cuttings are compacted in the blade area,
remove with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage, release the Handle knobs, and rotate or
fold the Upper Handle
.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities or
retailer for recycling advice.
Содержание WG751E
