13
INSTRUCTIONS
(continued)
For first time installation, read the instructions for
mounting your pallet fork attachment on your front loader
or skid steer. (See pages 13-16.)
Remove the bucket from your front end loader. Check
your loader to make sure it is in good working order.
MODELS MPF-1200 & MPF-2000
——————————————————
The Models MPF-1200 and MPF -2000 are for walk
behind Mini Skid Steer units equipped with the
"Universal" type attachment on the loader.
The Model MPF-1200 can handle loads up to 1,200 Ibs.
The Model MPF-2000 can handle loads up to 2,000 Ibs.
Always make sure latch pins engage to lock the frame
in place.
Connection instructions are similar to the ones for reg-
ular size skid steer units. (See page 15.)
MODELS MPF-1200B/G &
MPF-2000B/G
——————————————————
The Models MPF-1200B/G and MPF-2000B/G are for
Bobcat walk-behind Mini Skid Steer units and the Bobcat
S-70 small skid steer unit. It is also for the Gehl Model
1640 small skid steer.
The Model MPF-1200B/G is for loads up to 1,200 lbs.
The Model MPF-2000B/G can handle loads up to 2,000
lbs. Check your unit's lift capacity before handling loads.
Always check to make sure latch pins engage slots to
lock the frame in place.
Connection instructions are similar to the ones for reg-
ular size skid steer units. (See page 15.)
FORK TINE INSTALLATION
——————————————————
With loader arms lowered and completely rolled back,
shut down the power unit following the safety shutdown
procedure for your unit. Ensure that the locking assembly
on the tine is in the unlocked (UP) position. Place the top
of the fork on the top rail in the middle of the frame and
then rotate down. Slide the fork to the side to seat it on
the frame and, using the locking assembly that is on your
tine, lock in place. Install the following tine(s) in the same
fashion. Make sure the locking assembly has been set
into a notch on the top rail and therefore securing the tine
to the frame.
MODELS SSPF-1236 & SSPF-2000
——————————————————
The Pallet Fork Models SSPF-1236 and SSPF-2000 are
designed for Sub-Compact and Compact Tractors with
loaders having the universal skid steer type bucket quick
attach system and some smaller skid steer units.
The Model SSPF-1236 can handle loads up to 1,250 lbs
and has 36” long fork tines. This model is for Sub-
Compact Tractors generally below 30 hp.
The Model SSPF-2000 can handle loads up to 2,400
lbs. This unit is for small sized skid steer units and small-
er Compact Tractor loaders.
This model is for Compact Tractors generally below 40
hp and smaller size skid steers.
Connection instructions are on page 15.
MODELS JDPF-1236, JDPF-1242
& JDPF-2000
——————————————————
The Pallet Fork Models JDPF-1236 and JDPF-1242 are
designed for John Deere Sub-Compact tractors equipped
with John Deere loader modes: 200X, 200CX, 300X,
300CX, D-120, H-120, H-130, D-160, 220R, H-160, and
H-165. These loaders are equipped with the John Deere
Quick Change attachment means. The Model JDPF-1236
has 36” fork tines with load rating of 1,250 lbs. The Model
JDPF-1242 has 42” fork tines and a load rating of 1,250
lbs.
The Pallet Fork Model JDPF-2000 is designed for John
Deere compact tractors that have John Deere loader
models: 400X, 400CX, D-170, H-180NSL, H180MSL, and
512NSL. These loaders have the John Deere Quick
Change attachments means. The Model JDPF-2000 has
42” fork tines with load rating of 2,400 lbs.
Connection instructions for both models are on page
16.
14
Measure the width of your loader arms and figure how
to best attach the loader mounting brackets so the front
loader attachment is centered on your loader.
Assemble the four (4) lift brackets on the main frame
with the
5
/
8
” x 3” I.D. U-bolts. Leave the U-bolts loose.
Measure the width of each loader arm at the lower end
(where the lower pin goes through). Then position the
mounting brackets on each side for this width plus
1
/
8
” -
1
/
4
”. This will keep the loader attachment from having
excessive side movement.
NOTE:
The width of the loader arms will vary with the dif-
ferent makes and models of loaders. Depending on the
width of your loader and the relationship to the width of
the front loader attachment, you may need to use one of
the bracket mounting arrangements shown below. The
majority of loaders will best use the normal mounting
arrangement as shown in “A”.
Tighten the U-bolts that connect the brackets to the
main frame
ASSEMBLY – TRACTOR LOADERS
– PIN ON ATTACHMENT
COMPACT TRACTOR
LOADER BRACKETS FOR
MODEL FLPF-2000 PALLET FORK
INSTRUCTIONS
(continued)
MODEL FLPF-2000
——————————————————
The Universal Model FLPF-2000 Pallet Fork attachment
is recommended for tractors with an engine horsepower
rating of 20-40 hp.
Optional brackets are available to fit both pin-on and
some popular quick coupler front-end loaders. Brackets
must be ordered with the pallet fork attachment to mount
on your loader.
The Compact Tractor list of optional mounting brackets
is on this page.
The Model FLPF-2000 with 42” solid pallet forks can
handle loads up to 2,400 lbs. Load rating is figured with
the load about 20” in front of the fork lift frame and even-
ly distributed between the two fork tines.
