background image

2 of 12  

Workrite Ergonomics  |  (800) 959–9675  www.workriteergo.com

IMPORTANT NOTE!

You must complete initialization (Step 13) at the end of 

assembly or your work center WILL NOT FUNCTION PROPERLY.

WARNING: 

Maximum loading of table assembly is 300 lb (136 kg). Maximum load includes 

the weight of the table top itself, any equipment placed upon it, and any equipment suspended or hanging under 
it. Loading should be evenly distributed over table surfaces. “Payload Capacity” is the Workrite Ergonomics 
recommended maximum loading which includes the Workrite sourced worksurface.

Sierra 3-Leg
V = 120 VAC, 60 Hz / 4.25 A maximum

FLAMMABILITY: All worksurfaces used must meet UL962 flammability requirements 

•  Flame Spread Rating maximum 200

•  Smoke Developed Index maximum 450
WORKSURFACE SIZE: This frameset is designed to accommodate worksurfaces made from Industrial Particle Board  

with the following dimensions:

Dimensions

 (inches):

40"–46"wL

 × 

76"– 90" wR

 × 

23"–29"d

76"–88"wL

 × 

40"– 46" wR

 × 

23"–29"d

IMPORTANT SAFETY INSTRUCTIONS:

When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Sierra Work center.

DANGER:

 

To reduce the risk of electric shock, always unplug this Sierra Work center from the 

electrical outlet before cleaning. 

WARNING:

 

To reduce the risk of burns, fire, electric shock, or injury to persons:

1.  Unplug from outlet before putting on or taking off parts.
2.  Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3.  Use this furnishing only for its intended use as described in these instructions. Do not use attachments not 

recommended by the manufacturer.

4.  Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been 

dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and 

repair.

5.  Keep the cord away from heated surfaces.
6.  Do not use outdoors.
7.  Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8.  To disconnect, remove plug from outlet.
9.  Each surface intended to support an equipment payload capacity of 225 pounds.

FOR COMMERCIAL USE ONLY

SAVE THESE INSTRUCTIONS 

Содержание Sierra SEHX7890-4272OC Series













Отзывы: