background image

19

800.778.8779 | WORKHORSEPRODUCTS.COM

REGISTRATION FORM

FOR WARRANTY TO TAKE PLACE YOU MUST EMAIL THIS FORM BACK TO:

[email protected]

Although every effort has been made to provide accurate specifications, Workhorse Products does not assume any 
liability for damages, whether consequential or incidental, that may result from the use or misuse of the indicated 
specifications. Workhorse Products requires the use of a licensed industrial electrician for the installation of 
electrical service to equipment requiring electrical power.

Workhorse Products reserves the right to alter specifications in the manufacture of its products. It is understood and 
agreed that Seller’s liability for any equipment whether liability in contract, in tort, under any warranty, in negligence, 
in strict liability or otherwise shall not exceed the return of the amount of the purchase price paid by Buyer. Not 
withstanding the foregoing provision, under no circumstances shall Seller be liable for special, indirect or consequential 
damages. The price stated for the equipment is a consideration in limiting Seller’s liability. No action regardless of 
form, arising out of the transactions under this Agreement may be brought by Buyer more than fifteen (15) years after 
the cause of action has occurred. Our warranty is specified, is exclusive and no other warranty, whether written or 
oral, is expressed or implied. Workhorse Products specifically disclaims the implied warranties of merchantability and 
fitness for a particular purpose. Equipment manufactured or sold by Workhorse Products is warranted against defects 
in workmanship and materials for a period of one year from receipt by customer. All warranties initiate from date of 
shipment to original customer. Replacement parts are covered for the term of the equipment warranty period. Parts 
not under warranty are covered for thirty (30) days from receipt by customer. Any part found by Workhorse Products to 
be defective in material or workmanship within the stated warranty period will be replaced or repaired at Workhorse’s 
option without charge.

AFTER OBTAINING AN RMA# SEND RETURNED FREIGHT PREPAID TO:
3730 E. Southern Avenue, PHOENIX, AZ 85040 USA.

Written authorization must be obtained from Workhorse before any part will be accepted. Replacement parts are 
sent out freight collect. Parts sent out prior to receiving defective require a credit card hold for cost plus freight. 
Upon return of defective part, if it is deemed that the part was not damaged by customer but failed, the cost of the 
replacement part will be refunded.

This warranty does not extend to expendable parts such as filters, fuses, elements and brushes, casters. Workhorse 
does not warrant failure of parts or components resulting from misuse or lack of proper maintenance. Installation, 
inspection, and maintenance costs are the sole responsibility of the purchaser.

Company Name:

Address:

City:

State:

Country:

Zip Code:

Model Number:

Date Purchased:

Contact Name:

Phone Number:

Fax Number:

Email:

Cell Number:

Serial Number:

Date Purchased:

LIMITED WARRANTY

Содержание QUARTZ FLASH





















Отзывы: