background image

                                            PAGE 5

User Manual

       

 / Manual de uso

High-impedance (70V/100V line) (100W x 1 channel)

Low-impedance  (2x 50W @

 

 )

8

Ω

2. Set the speaker output to high-impedance by setting the DIP Switch number 10 

(14)

, according

to loudspeakers value 

[

100V] or [70V] corresponding to the maximum output voltage.

3. Use speaker cables to connect the [SPEAKERS A] 

   

terminal to the positive “+”

 

terminals 

2. Use speaker cables to connect the 

3. Use speaker cables to connect the 

     [SPEAKERS A]     ,  

  

terminals to the +, - 

     [SPEAKERS B]     ,  

  

terminals to the +, - 

of the speakers, and the [SPEAKERS B]      

terminals of the loaded speakers, 

terminals of the loaded speakers, 

terminal to the negative “-”

 

terminals.

  

In case of high-impedance connection,     terminals MUST NOT BE CONNECTED

Note 

:The speaker output is processed through a high pass filter (80Hz, 18dB/oct.).

Note 

:Take into account the maximum power loaded per channel 

(50W @ 8

Ω)

Maximum

 

output

 

voltage

:

100V

Maximum

 

output

 

voltage

:

70V

8

8

100W @ 70V or 100V

DIP switch body

1. Select 70V/100V position using the switch

 (15)

1. Select 8

 position using the switch

 (15)

Ω/16Ω

50W @ 8

Ω

50W @ 8

Ω

Note: In low impedance DOES NOT EXIST Bridge mode. Therefore, the
usual bridge connection (using both + terminals), are used ONLY in high
impedance mode. 

Note: Before operates the unit in this mode, please, check the switch (15) 
position (70/100V position)

EN

SPEAKERS

SETUP

SPEAKERS

SETUP

PA 100 MX

Содержание PA 100 MX

















Отзывы: