Especificaciones
Respuesta de frecuencia. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hz a 20 kHz
Impedancia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms (30 W)
Sensibilidad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 88 dB
Woofer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4" cono de polipropileno y suspensión de goma
Tweeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75" montaje central.
Dimensiones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 mm
diametro x 114 mm prof
Posiciones del transformador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 V(8W, 4W, 2W, 1W, 0.5W)
IC 4 PRO
IC 4/6 PRO User Manual/Manual de uso Página 4
IC 4/6 PRO User Manual/Manual de uso Page 1
These in-wall, or in-ceiling, speakers are designed to accurately reproduce music, including today's demanding digital signals.
In-wall speakers are designed so that the wall and the space behind it actually become the speaker cabinet. Mounted flush
to the wall, they require absolutely no floor space. The frames and grilles may be painted to blend with any decor. The
discrete, com-pact format is ideal for many applications where traditional speakers would be impractical or impossible.
In-wall speakers may be used independently where space is a consideration, or to bring music to additional rooms in the
house. They can also be used to enhance and enrich subwoofer and surround sound systems, for which they are especially
suited.
Speaker Placement
Once installed, in-wall speakers are not easily moved or repositioned. Take a little extra time to carefully consider a good
speaker location before you begin. Each room is unique, so decide what works best for you. Unlike traditional speakers,
in-walls mount flush and cannot be angled or aimed back into the listening area from the corners of a room. As a general
rule, the speakers should be mounted close to, or above, ear level, and at least one-third of the distance from the corner of
the room to the center of the wall or ceiling in which you will mount them.
Allow at least 1
1
2
" of clearance between the cut out and any studs or joists for the mounting hardware to work properly.
A mounting depth of 175 mm
measured from the face of the wall is also required. The speaker location and associated
mounting hardware should not conflict with any existing wires or pipes.
Hooking Up The Wires
The terminals will accommodate up to 16-gauge speaker wire, which should be used for longer connections (greater than 50
feet of wire). For shorter distances, 18 or 20 gauge speaker wire will be adequate. Leave about two feet of extra wire at the
speaker end to make installation and positioning of the speaker easier. Do not use staples, nails or other metal objects to
secure the speaker wire. The resulting short circuit could affect your system's performance, and could also damage
components in your system, espe-cially the amplifier. You will get the best sound quality and least amount of hum by keeping
the speaker wires away from other electrical wires and cables.
When connecting your in-wall speaker, it is very important to retain the correct polarity. To do this, be sure that the wire
attached to the right power "top" of audio transformer on the speaker connects to the "+", red, positive or hot terminal on the
amplifier. Similarly, the "C", black, negative or ground terminal of audio transformer on the speaker must connect to the
respective "-", black, negative or ground terminal on the amplifier.
Mounting the Speaker
Yes, you will be cutting a hole in the wall. With the right tools and a little extra care and preparation, installing the in-wall
speaker can be both quick and easy. Carefully cut out the hole drawn on the paper template at the perforated edge labeled
“CUT HERE FOR MOUNTING TEMPLATE”. (Note: The inside ring on the template can be used to shield the woofer while
you paint the frame.) Next, position the template (now a border) where you have chosen to mount the speaker, and trace
along the inside edge. Make your cuts along this line. A utility knife will make the cleanest cuts in drywall. A keyhole saw or
an electric jigsaw may also be used. Try to keep the cuts neat, however the frame will overlap the hole to hide any rough
edges. At this point, with the wall open, run the speaker wires into position, and again, leave about two feet of extra wire at
the opening.
Remove the grille from the frame by pressing the quick-turn mounting screws from the back of the speaker into the grille
itself.
Remove the thin piece of foam positioned under the grille, which was used to protect the speaker during
transport.
Attach the speaker wires to the speaker. With the grille removed, insert the speaker into the mounting hole. Use a phillips
head screwdriver to turn the screw slowly clockwise. The quick-turn mounting system and frame will sandwich or clamp
around the wall to hold the speaker in place. Do not overtighten. If you are unsure, consult a professional contractor.
Installing The Grille
The metal grille, as well as the frame, may be painted to match any room. If you choose to paint them, do so before attaching
the grille to the speaker. The grille is held in place by a friction fit and is difficult to remove once the speaker is installed. If the
grille feels a little loose, or you are concerned about a grille falling from a ceiling installation, we have provided a small
amount of putty, which you can apply (sparingly) to the inside rim of the speaker before you insert the grille. The putty acts
as an additional adhesive between the grille and the frame.
IC 4/6 PRO Ceiling Speakers Series
100 V(8W, 4W, 2W, 1W)
Especificaciones
Respuesta de frecuencia. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz a 20 kHz
Impedancia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms (60 W)
Sensibilidad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 88 dB
Woofer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5" cono de polipropileno y suspensión de goma
Tweeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75" montaje central.
Dimensiones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 mm
diametro x 171 mm prof
Posiciones del transformador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 V(50W, 30W, 15W, 5W, 3W)
IC 6 PRO
100 V(50W, 30W, 15W, 5W)
Diseño y especificaciones sujetas a cambio sin previo aviso
Selector de potencia de salida
