Worcraft SG04-1000 страница 45 Скачать руководство пользователя

Страница: 45 / 53

●

Children must not be allowed to clean and perform

maintenance on the fine-spray system without supervision.

Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut
off and an appropriate plug fitted in its place by an authorized
customer service agent. The replacement plug should have the

same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.

ASSEMBLY & DISASSEMBLY (fig 2, fig 3 and fig4)

Before any work on the machine itself, pull the mains

plug.
Assemble the spray gun head

Align the head and body, then rotate the machine body
clockwise. After the lock knob locked, it is means secured
assembled already. See fig.2.

Disassemble the spray gun head

Slide the SDS lock knob and then rotate the machine
body anti-clockwise, then pull out. See fig. 3.

Mounting the spray material tank

Screw the spray material tank onto the spray head and
fasten it claockwise.

OPERATION

Preparing for Operation

Spraying on the sides of water bodies (lakes, rivers,

etc.) or neighbouring surfaces in the direct catchment area
is not permitted.

When purchasing paint, varnish and spray material, pay
attention to their environmental compatibility.

Preparing the Spray Surface
Note:

Cover off the vicinity of the spray surface thoroughly and

generously.
The spray mist contaminates the environment. When spraying
in enclosures, surfaces not covered can become contaminated.
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding dust.

Suitable spray materials and recommended diluting agents

●

When diluting, pay attention that the spray material and

the diluting agent correspond.

When using a faulty diluting

agent, lumps can develop that can lead to clogging of the spray
gun.

Determine the viscosity of spray materials

This spray gun used for max viscosity of spray material is 80
DIN. So you need to determine the material viscosity by DIN
cup. If viscosity is too high, it need to dilute the material at first.
To determin the DIN value, do the steps as belows:

1. Begin with material and cup at room temperature.
2. Submerge the cup into the material.(alternately you may
cover the drain hole with your finger and fill the cup with the
material).
3. Quickly raise the cup (or remove your finger) and begin
timing.
4. Stop timing when the steady stream first breaks at about 1 or
2 inches below the drain hole.

Filling the spray material

–

Unscrew the spray material tank from the spray gun.

–

Fill the spray material into the tank and screw the tank firmly

to the spray gun.

Starting Operation

●

Observe correct mains voltage! The voltage of the

power source must agree with the voltage specified
on the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.

●

Pay attention that the power tool cannot draw in

dust or other contamination during operation.

Switching On

To save energy, only switch the fine-spray system on
when you are using it.
– Plug the mains plug into a socket outlet.
– Grasp the power tool and point it at the spray surface.
The power tool is equipped with a two-step trigger switch
9.
The first step starts the turbine. The second step
transports the spraying material.
– Pull the trigger switch 9

until spraying material starts to

come out.

Switching Off

– Release the trigger switch 9.
– Pull the mains plug from the socket outlet.

Adjusting the Spraying Capacity (see figure 5)

–

To adjust the requested spraying capacity, turn the

thumbwheel 8:

–

: Min. spraying capacity,

+: Max. spraying capacity.

Working Advice