Worcraft DS08-180, Инструкция по эксплуатации

Страница: 44 / 46

ASSEMBLY (Fig. 3)
Unpacking
Carefully remove the tool and all loose items from the outer
carton.
Retain all packing materials until after you have inspected and
satisfactorily operated the machine.
Before setting up, repair or maintenance of the
appliance you must always turn off the operating switch and
pull out the mains plug!
1. Mount the dust collect hose port onto the machine,
please refer to fig. 3.
2. Mount the side handle on the machine housing.
3. Mounting the sanding sheet onto the sanding pad.
OPERATION
Electronic control
This machine has the characteristics as below:
▪ Lock-on switch (5)
▪ Adjustable Speed (4)
▪ LED light belt (13)
▪ ON/OFF LED switch (12)
Adjusting the rotation speed (Fig. 4)
The speed of the machine is variable to suit different tasks. It
can be adjusted from 1500 min
-1
up to 2300 min
-1
by using the
thumb wheel. Turn in the counter clockwise direction to
decrease the speed and in the clockwise direction to increase
the speed. Generally, you should use the higher speed for fast
stock removal and the lower speed for more precise control.
Replace sanding pad (Fig. 5)
▪
Insert the hex wrench (size 5) into the hexagonal screw bolt
on the sanding pad
▪ Hold the sanding pad firmly, and then turn the wrench to
dismount the pad.
▪ Install new sanding pad by tightening the bolt.
Stick the sanding paper to the pad
Please ensure the holes on the sanding paper to fit the holes
on the pad accurately.
Light on LED working light (Fig. 6)
Before operation, turn on the LED switch to “I” position to light
on.
Switch the LED swtich to “0” position to turn off.
Connect to dust bag
Dust bag has already connected to the hose. Please
ensure the dust bag to be cleaned in due time.
Suction power adjustment (Fig. 7)
Reduce the suction power by turning the wheel to the
left, and increase by turning it to the right.
Operation on high wall (Fig. 8)
The machine can be backed with belt when climbing on
the ladders to sand high walls.
Working advice
▪ Begin sanding and carefully contact the work surface
as lightly as possible-just enough to keep the sanding
head flat against the surface.
▪ The joist in the sanding head allow the sanding disc to
follow the contours of the work surface.
▪ The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long in
any one place or there will be swirl marks. With
experience it will be very easy to create excellent results.
MAINTENANCE
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER
use solvents to clean plastic pats. They could possibly dissolve or otherwise damage the material.
Wear safety glasses while using compressed air.
Clean the vacuum swivel connector as too much dust will keep it from turning freely..
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appropriate recycling locations. Take your unwanted machines to your
local dealer. Here they will be disposed of in an environmentally safe way.
Li-ion batteries can be recycled. Deliver them to a disposal site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents:
EN60745-1:2009+A11:2010;
EN60745-2-3:2011+A2:2013+A11:2014+A12:2014+A13:2015; EN55014-1:2006/+A1
：
2009/+A2:2011; EN55014-2:2015; EN61000-3-3:2013; in accordance with the regulations 200
6/42/ЕС, 2014/30/ЕU.
NOISE/VIBRATION Measured in accordance with EN60745 the sound pressure level of this tool is <74dB(A) and the sound
power level is <85dB(A) (standard deviation: 3 dB), and the vibration is <4,34 m/s
2
.