Worcraft AG14-150S, Инструкция по эксплуатации

Страница: 49 / 63

(See fig 4)
WARNING: Ensure the angle grinder is switch off
and unplugged from the mains. Choose the guard suited to the
work you are carrying out, grinding or cutting.
Depending on whether your operation is cutting or grinding,
select the correct protective cover. Failure to use the right cover
for operation could result in injury.
When using a grinding or cutting-off wheel, the protective guard
must be fitted on the tool, so that the closed side of the cover
always points toward the operator.
Mounted the protective cover with the protrusion on the cover
band aligned with the notch on the bearing box. Then rotate the
cover around 180° and close the fixed lever. Then use hex
wrench to fasten and secure it in place.
To remove the protective cover, follow the installation procedure
in reverse.
The protective cover can be turned to a desired angle, but not
more than
45° on left side or right side.
ASSEMBLING THE ABRASIVE DISC (See fig 5)
Please proceed as follows when mounting the wheel/disk
1. Before mounting, remove the mains plug from the socket!
Ensure that the protective device is correctly installed.
2. Place the internal flange(2) on the drive shaft. Ensure that it is
in contact with the two flat areas.
3. Place the abrasive disk/wheels on the drive shaft. Ensure that
it is correctly in place.
4. Now screw the external flange(7) to the drive shaft, Ensure
that it is facing the right direction according to the different type
of disk/wheel used. In the case of abrasive disks, the flange is
inserted with the raised side towards the disk. In the case of
cutting-off wheels, the flange is inserted with the flat side towards
the wheels.
5. Press and hold the lock button (4) to lock the spindle and then
tighten the external flange with the spanner(3).
SWITCHING ON & OFF (See fig 6)
To start the tool, do as following steps:
Action 1: press down the locking off knob (9) and keep hold it.
Action 2: meanwhile press the switch trigger (8) until the tool
power on
If want to continous working, you need to keep pressing the
trigger.
To Stop the tool, do as following steps:
Release the switch and the machine will stop.
SPEED ADJUSTMENT (See fig 7)
The tool equipped a speed adjustment function for working on
different materials. Turn the speed wheel (11) forward to
decrease the speed, Turn it back to increase the speed.
WORKING ADVICE
Grinding and Surface Processing
In order to grind surface, you should use a coarse abrasive
disk with a sunken centre. You can use the abrasive disks
with diameter of 125mm(for AG14-125S) or 150mm(AG14-
150S). The maximum thickness of disks is 6mm.
Cutting metal
In order to cut rods, tubes and metal parts you should use a
cutting-off wheel with diameter of 125mm(for AG14-125S) or
150mm(AG14-150S). The maximum thickness of wheels in
this case is 3mm.
Cutting Stone Material
When cutting stone material you should use cutting-off wheel
with diameter of 125mm(for AG14-125S) or 150mm(AG14-
150S).
The maximum thickness of wheels in this case is 3mm.
Please use proper wheels to work. Failure to use the right
cover for operation could result in injury.
WARNING! Cutting operations with abrasive cutting-off
wheels are only allowed when using a cut-off guard.
Always approach the job at the same angle at which you
would like to cut. Maintain this angle during cutting and do not
exert any side pressure on the wheel.
Abrasive Disks
Ensure that the speed to which the machine is set is sufficient
for the accessories chosen.
Use only abrasive disks with a diameter of up to 125mm(for
AG14-125S) or 150mm(AG14-150S).
Before mounting the disks remove the mains plug from the
socket!
Note: Expe
ct a “rain of sparks” when the disk comes into
contact with metal.
While grinding, always maintain the correct angle between
the disc and working surface. Of 15-
20°. This procedure ideal
avoids overloads.
MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the motor. Regularly clean the machine
housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come
off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents
may damage the plastic parts.
The machine requires no additional lubrication. If a fault occur, e.g. after wear of a part, please contact your local dealer
’s service.
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appropriate recycling locations. Take your unwanted machines to your
local dealer. Here they will be disposed of in an environmentally safe way.
Li-ion batteries can be recycled. Deliver them to a disposal site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).