Woodward APECS DPG-2101-001 страница 27 Скачать руководство пользователя

Страница: 27 / 50

Manual 36526A

DPG-21XX-00X Digital Controllers

Woodward

Installing Universal PST

Instructions to Install from CD-ROM:

When you insert the DPG Software Calibration Kit’s CD-ROM into your computer,

the “autorun” file on the CD will attempt to launch the “setup.exe” program. If the

“autorun” feature is disabled on your computer or does not start the setup program

you can launch the program manually. To start the installation manually, explore

the contents of the CD then double click on the “setup.exe” file.

Instructions to Install from the Downloaded File:

The file downloaded from the Woodward web site contains two files:

“ReadMeFirst.txt” and “setup.exe”. Run the downloaded file to extract its contents

to a folder you choose on your computer’s hard drive. Then run the “setup.exe”

program from the folder you extracted it to.

IMPORTANT:

The installation program will detect operating system components older than those

required by the "Universal PST" application. In this case the installation program

will ask if you want to update Windows. If you do not want "setup" to update your

system then you can not use the "Universal PST" application on this computer.

Read the setup program's instructions carefully as they appear and respond as

needed. The installation may take as long as 7 minutes depending on your

computer's power and operating system. Do not interrupt the installation program

even though it may appear as

though it is not running.

NOTE: Administrator rights may be needed to install on some Microsoft Windows

operating systems (such as Windows XP Professional) for the setup program to

properly register application resources.

Wiring the COMM Port to a PC

To construct a communications cable to use between the DPG’s COMM port and

your PC’s RS-232 serial port refer to the table and wiring diagram below.

NOTE—Remote access via the COMM port is intended for

connection only while programming, tuning and troubleshooting

the control/engine. It is a service port and not intended for

permanent connection of a PC and/or cable.

RJ11 OR

RJ12

POSITION

DPG-21XX SIGNAL

CONNECTS TO:

No connection

N/C

Transmit data to PC

PC receive (RxD)

DB9 pin 2

Receive data from PC

PC transmit (TxD)

DB9 pin 3

COMMON

PC common

DB9 pin 5

+5 Vdc (Do NOT

connect at the PC end)

N/C

No connection

N/C

DB9F

RJ11M

Содержание APECS DPG-2101-001



















































Результаты поиска

Содержание APECS DPG-2101-001

Отзывы:

Похожие инструкции для APECS DPG-2101-001

Бренды по названию

Популярные бренды

Woodward APECS DPG-2101-001, Руководство пользователя

Результаты поиска

Содержание APECS DPG-2101-001

Отзывы:

Похожие инструкции для APECS DPG-2101-001

Бренды по названию

Популярные бренды