manualshive.com logo in svg

Woods RM550, Руководство оператора, Страница: 27 / 48

Поделиться
Скачать
Woods RM550 Скачать руководство пользователя страница 27

25

PN 55191 (4/22/99)

TROUBLE SHOOTING

BELT CONDITIONS

PROBLEM

POSSIBLE CAUSE

SOLUTION

Belt slippage

Mower overloading; material too

Reduce tractor ground speed but

tall or heavy

maintain full PTO rpm. Cut material

twice, one high pass and then mow

at desired height. Cut a partial

swath.

Oil on belt from overlubrication

Be careful not to overlubricate.

Clean lubricant from belt and pulleys

with clean rag. Replace oil-soaked

belt.

Belt hung up or rubbing

Check belt position in pulleys and

idlers. Check belt for free travel in

pulleys. Check under mower and

around blade spindle shafts for wire,

rags, or other foreign material.

Clean all material from under

mower.

Frayed edges on belt

Belt misaligned

Re-align belt. Be sure belt does not

cover

rub any other part while running.

Pulley misalignment

Inspect to ensure belt is running in

center of backside idler. Shim idler

as necessary to align.

Belt rollover

Pulley misalignment

Re-align.

Damaged belt

Replace belt.*

Foreign object in pulley grooves

Inspect all pulley grooves for rust,

paint or weld spots and remove.

Worn pulley groove

Replace pulley.

Damaged belt

Rollover, high shock loads or

Replace belt.*

installation damage

Belt breakage

High shock loads

Avoid abusive mowing. Avoid hitting

the ground or large obstructions.

Belt came off drive

Check pulleys for foreign material in

grooves. Avoid hitting solid objects

or ground.

* Check belt for damage by laying it flat on floor. If belt does not lie flat (has humps or twists), which indicates broken

or stretched cords, it must be replaced.

Содержание RM550

















































Отзывы:

Нет отзывов