background image

CHECKING GAS PRESSURE

27

   

Install and attach 

1

/

2

" gas line onto shut-off valve.

Figure 34 - Gas Pressure Check at Gas Valve 

Pressure Test 

“IN”

Pressure Test 

“OUT”

HI/LO 

Knob

Pilot Adjustment 

Screw 

Do not use open flame to check for gas leaks.

WARNING

Control knob 

Ignitor

 STOP! Do not install theappliance. Contact your dealer immediately.

2. To ease installation, a 

48

"

x1/2"

 flex line with manual shut-off 

 

valve has been provided with  this appliance.

1. Check  gas  type. The  gas  supply  must  be  the  same  as stated on the 

  

appliance’s rating decal. If the gas supplyis different from the fireplace,

3. After completing gas line connection, purge air fromgas line 

and test all gas joints from the gas meter to thefireplace for leaks.
Use a solution of 50/50 water andsoap or a gas sniffer.

4. To adjust flame height, turn HI/LO knob to HI to getmaximum

 pressure  to  burner.  Turn  HI/LO  knob  to  LO to  get  minimum 
pressure.

5. To  check  gas  pressures  at  valve,  turn  captured  screwcounter

 clockwise  2  or  3  turns  and  then  place  tubingto pressure gauge 
over  test  point.  Turn  unit  to  high.  

See Figure  34.  

After  taking 

pressure reading, be sure and turn captured screw clockwise firmly 

to reseal. Do not overtorque. Check test points for gas leaks.

6. The  appliance  and  its  appliance  main  gas  valve  must  be 

disconnected   from  the  gas  supply  piping  system  during  any 
pressure testing of that system at test pressures in excess of 1/2 psi 
(3.5  kPa).  The  appliance  must  be  isolated  from  the  gas  supply 
piping  system  by  closing  its  equipment  shutoff  valve  during  any 
pressure  testing  of  the  gas  supply  piping  system  at  test  pressures 
equal to or less than 1/2 psi (3.5 kPa).

ELECTRICAL INSTALLATION 

ELECTRICAL WIRING

This fireplace will work without any electrical supply. Electricity is only needed to operate blower.

NOTE: If installed in mobile home, fireplace must be bolted securely to floor. 

WARNING

Verify proper operation after servicing. 

 

CAUTION

Label  all  wires  before  disconnecting  when servicing  controls. 
Wiring  errors  can  cause improper and dangerous operation.

Electrical connections should only be performed by a qualified, licensed electrician. Main power must be off 

when connecting to main electrical power supply or performing service. All wiring shall be in compliance 

with all local, city, and state codes. The appliance, when installed, must be electrically grounded in 
accordance with local codes, or in the absence of local codes, with the 

National Electrical Code ANSI/ 

NFPA 70 (latest edition) 

and 

Canadian Electrical Code, CSA C22.1.

Содержание DV32CV













































Отзывы: