Wood-mizer LX450DB-A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

Wood-mizer LX450DB-A Скачать руководство пользователя страница 6

Debarker Installation

Debarker Installation

2

2-1

DB17doc072219

Debarker Installation

SECTION 2 DEBARKER INSTALLATION

DANGER!

On electric mills, hazardous voltage inside the

disconnect box, starter box, and at the electric motor can
cause shock, burns, or death. Disconnect and lock out
power supply before performing debarker installation! Fol-
low all applicable electrical codes.

DANGER!

Before performing any service to this equip-

ment, turn the key to the OFF (0) position, remove the key,
and disconnect the sawmill battery ground terminal. Failure
to do so will result in serious injury or death.

CAUTION!

Due to various design changes and past retro-

fits and options, you should very carefully look your mill
over to determine Debarker compatibility before beginning
Debarker installation.

2.1

Debarker Installation

DANGER!

Always disengage the blade and shut off the

sawmill engine before installing the debarker. Failure to do
so will result in serious injury.

IMPORTANT!

Sawmills are equipped with pre-drilled

Debarker mounting holes.

Verify hole locations before

beginning Debarker installation. Proper hole location is
imperative for safe and effective Debarker operation.

1.

Open the blade housing cover.

«
...
4
5
6
7
8
...
»

Содержание LX450DB-A









































Отзывы:

Нет отзывов