Wood-mizer LMS-A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 42

Wood-mizer LMS-A Скачать руководство пользователя страница 15

LubeMizer Installation

Pump Installation And Wiring (All LT30/LT40 Sawmills)

LubeMizer Installation

LMS99doc032619

1-11

1

7.

Use the provided 1/4-20 x 3/4" hex head bolt and 1/4-20 self locking nut to secure the 1/2"
hose clamp to the back of the blade housing as shown.

NOTE:

Older revision mills do not have a hole in this location. Locate and drill one 9/32"

hole as shown below. Be sure to unbolt the main fuel line hose clamps

shown in Figure

and move the fuel line hose out of the way before drilling.

See Figure 1-9.

8.

Install the provided 14" length of 3/8" lube hose and the provided 5/8" hose clamp to the
filter. Using the provided 1/4-20 carriage bolts and 1/4-20 locking nuts, secure the 5/8"
hose clamps on either side of the filter in place. Be sure to install the carriage bolts from
the top.

NOTE:

Older revision mills do not have holes in this location. Locate and drill two 3/8"

diameter holes as shown in the following graphic.

See Figure 1-10.

FIG. 1-9

9/32” Diameter Hole

3H0749-2

11 3/4”

5 5/8”

«
...
13
14
15
16
17
...
»

Содержание LMS-A











































Отзывы:

Нет отзывов