Wood-mizer Incline Log Deck Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 35

Wood-mizer Incline Log Deck Скачать руководство пользователя страница 6

Safety Instructions

Safety Instructions

1

1-2

MHdoc112315

Safety

1.2

Safety Instructions

NOTE:

ONLY safety instructions regarding personal injury are listed in this section.

Caution statements regarding only equipment damage appear where applicable
throughout the manual.

Observe Safety Instructions

IMPORTANT!

Read the entire Operator's Manual before

operating the unit. Take notice of all safety warnings
throughout this manual and those posted on the equipment.
Keep this manual with this equipment at all times,
regardless of ownership.

Also read any additional manufacturer’s manuals and
observe any applicable safety instructions including
dangers, warnings, and cautions.

Only persons who have read and understood the entire
operator's manual should operate this equipment. The
equipment is not intended for use by or around children.

IMPORTANT!

It is always the owner's responsibility to

comply with all applicable federal, state and local laws,
rules and regulations regarding the ownership, operation
and towing of your Wood-Mizer equipment.

!

!

«
...
4
5
6
7
8
...
»

Содержание Incline Log Deck




































Отзывы:

Нет отзывов