Wood-mizer BMT200 Скачать руководство пользователя страница 8

Страница: 8 / 79

General Information

Safety

2-2

DS12doc060917

General Information

Blade Handling

WARNING!

Always wear gloves and eye protection when

handling bandsaw blades. Keep all persons away from
area when coiling or carrying a blade.

WARNING!

Before installing the blade, inspect it for dam-

age and cracks. Always handle the blade with extreme
care. Use suitable carrier equipment for transporting the
blades.

Machine Operation

DANGER!

Make sure all guards and covers are in place

and secured before operating the toothsetter. Failure to do
so may result in serious injury.

DANGER!

Keep all persons away from moving parts when

operating this machine. Failure to do so will result in serious
injury.

DANGER!

Always keep hands away from moving bandsaw

blade. Failure to do so will result in serious injury.

WARNING!

Always wear eye protection when operating

this machine. Failure to do so may result in serious injury.

WARNING!

Secure all loose clothing and jewelry before

operating this machine. Failure to do so may result in seri-
ous injury or death.

WARNING!

The toothsetter should be operated only by

adults who have read and understood the entire operator’s
manuals.

WARNING!

The illumination at the operator’s position

should be at least 300 lux. The light source can not cause
stroboscopic effect.

WARNING!

If at any time you need to immediately stop the

machine, press the Emergency Stop (E-Stop) button.
Before operating the machine again, turn the E-Stop button
clockwise to release. The machine will not start until the
E-Stop button is released.

Содержание BMT200
















































































Результаты поиска

Содержание BMT200

Отзывы:

Wood-mizer BMT200, Инструкция по безопасности, эксплуатации, техническому обслуживанию и каталог запасных частей, Страница: 8 / 79

Результаты поиска

Содержание BMT200

Отзывы: