Wood master FORCE 30 Скачать руководство пользователя страница 23

Страница: 23 / 44

Force 30 Owners Manual

2015

In phase two, the soft start level, the auger feeds the

burner 5 times with three second operation intervals on the

auger before it goes over completely to full burn mode. The

three values in this menu can be changed.

The next menu shows the burn mode the burner. The

power displayed is the approximate input power. This is

where the settings for the burner are changed when adjust

ing the furnace with a flue gas analyzer. This is made by

adjusting the time for the feeding of the auger and time be

tween the feeds. You can also select the mode in this menu.

The choices are LOW and HIGH, where the user determines

the feed rate, and AUTO mode, where the PLC determines

the feed rate. See step 5 for adjusting AUTO mode. Press

buttons 2 and 3 together to change this value. You do not

have to press button 4 and the white button prior to chang

ing this setting.

The Startdos value in this menu (this is a different setting

than the startdos previously described) is adjustable be

tween 100 and 400 grams and is the adjustment used when

the burner is in Auto burning mode. The MAX RUNTIME

value is how long the burner will run before shutting down

to self clean. The default value shown is 1/2 an hour. If heat

is still called for, the burner will restart after the cleaning

is completed. You can also read the operation time of the

burner and how many times it has started.

BURNING MODE LOW

POWER kW 15.0

ON +09.5

OFF

+10.0

Menu/Ok

SOFT START

SCREW ON +03.5

SCREW OFF +15.0

NO OF 05.0

Menu/Ok

STARTDOS +125 g

MAX 0.5

RUNTIME +00000

No OF 00000

Operation

This menu displays the current room temperature and

allows you to set the desired temperature. The selected tem-

perature can be changed. The room temp is the temperature

that the supplied temp sensor is detecting.

The burner comes with a temperature sensor that starts

and stops the burner. A wall mounted thermostat can be

wired directly to the PLC on the burner. If a wall mounted

thermostat is used, disconnect the temperature sensor. If a

wall mounted thermostat is used, the selected value can no

longer be changed in this menu, and is instead controlled by

the thermostat.

Menu/Ok

OPERATE TEMP

ROOM TEMP +69

SELECTED +72

Содержание FORCE 30













































Результаты поиска

Содержание FORCE 30

Отзывы:

Похожие инструкции для FORCE 30

Бренды по названию

Популярные бренды

Wood master FORCE 30, Руководство пользователя

Результаты поиска

Содержание FORCE 30

Отзывы:

Похожие инструкции для FORCE 30

Бренды по названию

Популярные бренды