Wood master FORCE 30 Скачать руководство пользователя страница 4

Страница: 4 / 44

Force 30 Owners Manual

2015

Sweeping

The chimney should be inspected and cleaned as needed, typically twice a year. This is to be done by qualified

persons. Regular cleaning of heating surface of the furnace will help the furnace operate at the highest pos

sible efficiency. Shut off furnace, disconnect power and allow the furnace to cool before attempting to clean

the furnace.

Warning!

Always disconnect the power to the furnace before any cleaning or maintenance.

Service agreements increases operation length and life of the unit. For more information contact your local

WoodMaster dealer.

Replacement parts should only be genuine Northwest Manufacturing, Inc. components. Your WoodMaster

dealer can supply the genuine service parts and install them. They can then reevaluate the system and provide

a flue gas analysis. Failure to perform a flue gas analysis may void your warranty.

Emission Standards

Visit the EPA Burnwise website, http://www.epa.gov/burnwise/index.html for information on wood fuel fired

appliances, as well as a list of approved appliances.

Safety Standards

Guardian info: Solid Fuel Burner System. Listed by Guardian Fire Testing Laboratories Inc. Tested and

listed to THE Applicable Sections of UL-391, ETLM 78-1, ASTM-E 1509 & CAN/CSA-B366.1 EPA EXEMPT PER

40CFR60.53A, METHOD 28A

Safety

Содержание FORCE 30













































Результаты поиска

Содержание FORCE 30

Отзывы:

Похожие инструкции для FORCE 30

Бренды по названию

Популярные бренды

Wood master FORCE 30, Руководство пользователя

Результаты поиска

Содержание FORCE 30

Отзывы:

Похожие инструкции для FORCE 30

Бренды по названию

Популярные бренды