Wolfson WM8580 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 103

background image

WM8580

Production

Data

w

PD, Rev 4.7, March 2009

70

REGISTER

ADDRESS

BIT LABEL DEFAULT

DESCRIPTION

0 AUDIO_N

- Linear

PCM

Identification

0 = Data word represents audio PCM samples.
1 = Data word does not represent audio PCM samples.

1

PCM_N

-

Indicates that non-audio code (defined in IEC-61937)
has been detected.
0 = Sync code not detected.
1 = Sync code detected – received data is not audio
PCM.

2

CPY_N

-

Recovered Channel Status bit-2 (active low).
0 = Copyright is asserted for this data.
1 = Copyright is not asserted for this data.

3

DEEMPH

-

Recovered Channel Status bit-3
0 = Recovered S/PDIF data has no pre-emphasis.
1 = Recovered S/PDIF data has pre-emphasis

5:4 REC_FREQ

[1:0]

--

Indicates recovered S/PDIF clock frequency:
00 = Invalid
01 = 96kHz / 88.2kHz
10 = 48kHz / 44.1kHz
11 = 32kHz

R49

SPDSTAT

31h

(read-only)

6

UNLOCK

-

Indicates that the S/PDIF Clock Recovery circuit is
unlocked or that the input S/PDIF signal is not present.
0 = Locked onto incoming S/PDIF stream.
1 = Not locked to the incoming S/PDIF stream or the
incoming S/PDIF stream is not present.

Table 69 S/PDIF Status Register

The interrupt and update signals used to generate INT_N can be masked as necessary. The MASK
register bit prevents flags from asserting INT_N and from updating the Interrupt Status Register
(R43). Masked flags update the S/PDIF Status Register (R49).

REGISTER

ADDRESS

BIT LABEL DEFAULT

DESCRIPTION

R37

INTMASK

25h

8:0 MASK[8:0]

000000000

When a flag is masked, it does not update the Interrupt
Status Register or assert INT_N.
0 = unmask, 1 = mask.
MASK[0] = mask control for UPD_UNLOCK
MASK[1] = mask control for INT_INVALID
MASK[2] = mask control for INT_CSUD
MASK[3] = mask control for INT_TRANS_ERR
MASK[4] = mask control for UPD_AUDIO_N
MASK[5] = mask control for UPD_PCM_N
MASK[6] = mask control for UPD_CPY_N
MASK[7] = mask control for UPD_DEEMPH
MASK[8] = mask control for UPD_REC_FREQ

Table 70 Interrupt Mask Control Register

Downloaded from

electronic components distributor

«
...
68
69
70
71
72
...
»

Содержание WM8580








































































































Отзывы:

Нет отзывов

Похожие инструкции для WM8580

Бренд: Datcon Страницы: 40

Sky Champion S-20R

Бренд: Hallicrafters Страницы: 5

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 28

Бренд: Alan Страницы: 6

Бренд: Strong Страницы: 15

Бренд: RF Electronics Страницы: 13

Бренд: Regin Страницы: 2

Бренд: Teleco Страницы: 8

Бренд: Aventura Страницы: 6

Бренд: FUTABA Страницы: 169

Бренд: WHD Страницы: 4

Бренд: AOR Страницы: 1

Бренд: First Alert Страницы: 1

Бренд: SilverStone Страницы: 2

Бренд: Omega Страницы: 24

Бренд: Kantronics Страницы: 10

DEC 664HD/USB/REC

Бренд: Majestic Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды