manualshive.com logo in svg

wirsbo proMIX 101, Руководство по установке

Поделиться
Скачать
wirsbo proMIX 101 Скачать руководство пользователя страница 25

INSTALLATION - STEP 8

COMPLETING THE INSTALLATION

Once you have successfully tested all the wiring and found
that everything is operational, you are ready to complete the
installation.

1) Make sure all power to the devices and terminal blocks is

off, and remove any remaining jumpers from the terminals

2) Reconnect the terminal blocks to the control by carefully

aligning them with their respective headers on the control

3) Push the terminal blocks into the headers — they should

snap firmly into place 

(See fig. a)

4) Install supplied safety dividers between unpowered sensor

inputs and powered or 120 VAC wiring chambers

5) Apply power to the control

NOTE:

The operation of the control on power up is

described in the Control Function Overview section
of this manual (page 33).

Cleaning the Control

• Moisten cloth with water and wring out prior to wiping

control

• Do not use solvents or cleaning solutions on the control

23

INST

ALLA

TION

INSTALLATION - Step 8 - Completing the Installation

11

12

14

13

UnO

Sw

Com BRet

S3

Mix
S1

a

Содержание proMIX 101

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды