manualshive.com logo in svg

Wipaire Wipline 2100, Руководство по обслуживанию и инструкции

Поделиться
Скачать
Wipaire Wipline 2100 Скачать руководство пользователя страница 42

SERVICE MANUAL & ICA

WIPLINE 2100 & 2350 FLOATS

Page 42         

          

Revision N                                

         P/N  1002549

For normal operation (electrical power pack) the handle is in the neutral position (handle pointed to the neutral 

position.) If electrical pump should not operate, select to gear up (handle pointed forward) or gear down (handle 

pointed aft). Insert stowable handle in pump and pump gear to desired position. If pump should leak, remove snap 

ring under handle and pull out inner cylinder. Replace “O” rings and reinstall.

7.5 HAND PUMP OPERATION

The gear selector is an electrical switch which changes pump direction of the electro power pack for gear up or 

down. The red light on panel indicates the pump is running. The four (4) green lights indicate the landing gear is 

down. The four (4) blue lights indicate the gear is up for water landing. The top two lights of each cluster refer to 

the nose gear position. The bottom two refer to the main gear.

BLUE - GEAR UP “WATER”

GREEN - GEAR DOWN “LAND”

CAUTION!!

Do not land on water with gear in extended position. Aircraft will nose over.

7.6 GEAR SELECTOR

Grease zerks are provided on all wheels and bearings and should be greased every 25 hours or after an 

extended period of time in the water. Water/heat resistant grease is recommended.

At brake installation, apply STA-Lube synthetic brake and caliper grease or equivalent to brake caliper pins.

The brakes need no special care other than to maintain the brake disc free of rust, which causes premature brake 

lining wear. Bleeding is carried out in the usual manner from the bottom up.

Main wheel tires are standard 5.00 X 5, 6-ply Type III aircraft tires, inflated to 50 +/- 5 psi. (Refer to Figure 5-5).

7.7 MAIN WHEELS AND BRAKES

In addition to position lights on selector head, gear position should be visually inspected before landing. Check 

nose gear positions by looking at gear to determine position. Main gear has a position indicator rod on the float 

top deck. Check position of both right and left rod before landing.

7.8 VISUAL POSITION INDICATORS MAIN AND NOSE GEAR

Содержание Wipline 2100







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды