Wipaire Wipline 2100 Скачать руководство пользователя страница 33

Страница: 33 / 70

SERVICE MANUAL & ICA

WIPLINE 2100 & 2350 FLOATS

P/N 1002549

Revision N

Page 33

As coded in the Inspection Time Limits chart in this section, there are items to be checked each 25, 50, 100, and

200 hours. Also, there are notes on special items which may require servicing at more frequent intervals.

• When conducting an inspection at 25 hours, all items marked for 25 hours would be accomplished.

• When conducting an inspection at 50 hours, the 25 and 50-hour items would be accomplished.

• When conducting an inspection at 100 hours, the 25, 50, and 100-hour items would be accomplished.

• When conducting an inspection at 200 hours, the 25, 50, 100, and 200-hour items would be accomplished.

• A complete inspection (Annual Inspection) would include all 25, 50, 100, and 200-hour items.

When servicing float hull and amphibian components, below is list of recommended lubricants and “protection”

products. This lists products used by Wipaire during assembly of the floats.

There may be equivalent products that are just as satisfactory for protection. It is recommended if trying different

products, to inspect them frequently so as to determine their effectiveness.

Protection of nuts, bolts, hydraulic lines or metal surfaces

Zip D-5029NS Corrosion Inhibiting Compound

Zip Chemical Company

CRC – SP400 Soft Seal

CRC Industries

General Lubricants

LPS 1, LPS 2 and LPS 3

LPS Industries

Wheel Bearings

*HCF Grease, P/N 605

HCF Industries

*Aeroshell 22

Shell Global Solutions

*Green Grease, Multi-Purpose

Green Grease Inc.

*Aviation Grease SHC 100

ExxonMobil Aviation Lubricants

* If existing grease cannot be identified you must lubri-flush all float grease fittings until visibly exhausting all old

grease and new grease is coming out. Additionally if you cannot determine existing grease in wheel bearings,

completely clean and repack bearings with new grease.

Rust Protection

Boeshield T9 Rust Protection

Boeing Company

ACF-50 Rust Protection

Corrosion X

Corrosion Technologies Corporation

6.2 SERVICE SCHEDULE

Содержание Wipline 2100







































































Результаты поиска

Содержание Wipline 2100

Отзывы:

Бренды по названию

Популярные бренды

Wipaire Wipline 2100, Руководство по обслуживанию и инструкции

Результаты поиска

Содержание Wipline 2100

Отзывы:

Бренды по названию

Популярные бренды