WinSystems PCM-MIO-A-1 Скачать руководство пользователя страница 32

Страница: 32 / 36

PCM-MIO-A-1/Best Practices

v1.0

www.winsystems.com

Page 32

Contact Points

WINSYSTEMS boards mostly use connectors with gold finish contacts.

Gold finish contacts are used exclusively on high-speed connections.

Power and lower speed peripheral connectors may use a tin finish as an

alternative contact surface. It is critical that the contact material in the

mating connectors is matched properly (gold to gold and tin to tin).

Contact areas made with dissimilar metals can cause oxidation/corrosion,

resulting in unreliable connections.

Pin Contacts

Often the pin contacts used in cabling are not given enough attention. The

ideal choice for a pin contact would include a design similar to Molex or

Trifurcon designs, which provide three distinct points to maximize the

contact area and improve connection integrity in high shock and vibration

applications.

Power Down

Make sure that power has been removed from the system before making

or breaking any connections.

I/O Connections OFF

—Turn off all I/O connections before connecting

them to the PCM-MIO-A-1 or any other I/O cards. Connecting hot signals

can cause damage whether the embedded system is powered or not.

Mounting and Protecting the I/O Module

To avoid damage, mount the PCM-MIO-A-1 properly. Standoff kits are

available and recommended for use with the PCM-MIO-A-1.

Placing the PCM-MIO-A-1 on mounting standoffs

—Be careful when

placing the PCM-MIO-A-1 on the mounting standoffs. Sliding the board

around until the standoffs are visible from the top can cause component

damage on the bottom of the board.

Do not bend or flex the PCM-MIO-A-1

—Bending or flexing can cause

irreparable damage. Embedded computer modules are especially

sensitive to flexing or bending around ball grid array (BGA) devices. BGA

devices are extremely rigid by design, and flexing or bending the

embedded computer module can cause the BGA to tear away from the

printed circuit board.

Power Supply OFF

—Always turn off the power supply before

connecting to the I/O Module. Do not hot-plug the PCM-MIO-A-1 on a

host platform that is already powered.

Содержание PCM-MIO-A-1





































Результаты поиска

Содержание PCM-MIO-A-1

Отзывы:

Бренды по названию

Популярные бренды

WinSystems PCM-MIO-A-1, Руководство по эксплуатации продукта

Результаты поиска

Содержание PCM-MIO-A-1

Отзывы:

Бренды по названию

Популярные бренды