Windsor PASSPORT PSP-I, Руководство пользователя

Страница: 4 / 16

NOTE: powdered
soap
is used. with
hot
water before tank.
A.
Reinstall
tank and dome.
Make
hoses
are
snug
OPERATING THE
PASSPORT
WARNING
the IMPORTANT INSTRUC-
TIONS before operating,
attention to
care and use
of power
cord. Only operate i f cord is
in
condition.
NOTE: Vacuum carpet and make
sure
it
of surface before cleaning.
to power
cord. Make bop in power
Prom
end.
(DIAGRAM A. )
2. Adjust brush height by knob
front
of machine. Pointer on
side
indicates carpet height.
LOW
HIGH- 1
NOTE: move height
may
cause
brush circuit breaker
to
Raise
brush and
reset breaker.
3. Turn valve to 'CARPET CLEAN-
ING'
(DIAGRAM
C:
switch.
!%??
4.
Plug power
cord into a
grounded wall
Turn
h e
vacuum switch and brush
NOTE:
water loam the
tank may cause water foam to
enter the
vacuum
This over-
the
vacuum motor and vacuum
breaker
will
trip.
6.
intermittent pump
to
dispense cleaning solution.
backwards.
Release
pump about
12 inches before
the end each cleaning
pass. will solution
from carpet.
CAUTION:
While operating machine, check
excessive
foam
in
the tank.
If
foam
is
present, add a
to
covecy
7.
Empty
recovery
tank when approximately
full.
CAUTION :
DO
not
use me
tank to
the
tank. unless it CLEAN. Sediment in
tank damage pump and dog
he spray rendering
PASSPOR T-I
ACCESSORY TOOLS
The PASSPORT
is easily
adapted for use
the following
,
Never operate
with water C.
Turn
solution valve
to
'ACCESSORY
TOOL- position
(DIAGRAM
dome and vacuum hose from
accessory tool in its place.
3. Attach
hose accessory
to brass quick
fitting on
left
side of machine.
2. Remove recovery (white from
4.
Remove dome and recovery
5.
Fill
tank with
p e r
6.
tank dome.
on vacuum and
switches only.
CAUTION: Do not on brush switch.
Damage to carpel
Before making any adjustments
or
repairs to
h e machine, disconnect power cord from
1.
unused cleaning solution.
2. Inspect and clean solution screen.
3. flush pumping
system
1 to 2
4. Rinse lank dean
water.
5.
any lint
or debris
brush and
shoe.
6. Check spray and dean solenoid
if
required.
NOTE: Always store machine brush in
'store' position.
of dean
hot water.
PERIODIC MAINTENANCE
quart
vinegar to of
hot water) or an
(mixed as through extractor.
This will help
prevent
build-up of alkaline
residue in system.
2. I f spray become clogged,
spray tips, wash them
vinegar
and
blow dry.
1. Twice a a white vinegar
NOTE: Do not use pins, etc. lo
jets
as
this
will
spray
3. spray jets continue to drip
is
turned off. the solenoid valve
cleaning. MAINTENANCE Instructions
5/2/94
and on your
machine.
Frayed or cracked hoses should
be repaired to eliminate vacuum
solution pressure loss. Because
electrical cable lie on wet carpet
times. cable must be well insulated
and
cable
screws
kept
If
cable insulation broken or bayed.
or
replace
it immediately. take
chances
with
an or shock
PROTECT FROM
FREEZING
If it
necessary
lo store
below
4"
C the
must protected
with
a methyl hydrate (window washer)
NOTE:
Do
not
use
or
system antifreeze.
Add
washer
to
tank.
2. Turn on pump
solutionsprays
3.
unused portion of
from tank
MAINTENANCE
INSTRUCTIONS
WARNING
1. Only maintenance personnel
to
perform following repairs.
repairs.
connections.
2. Unplug (he machine
3. to
lor proper
BRUSH ASSEMBLY
1. Remove guard, brush guard
and bearing each
end
of brush
Loosen (2) hex on
studs and
motor and remove
from motor pulley.
3.
Remove
brush assembly
from
. .
Replace brush or bearings
required.
proper tension. should
be
taught
(Do
not To belt.
hex nuts, rotate rearward
retighten nuts.
4.
When brush, check belt
ACCESS CHASSIS
COMPONENTS
1.
Lilt
off
recovery tank and
set
2.
solution-drain hose
Remove
(A)
bolts holding to
Raise tank and pull hose
chassis. Remove pump
hose
torn rank and tay aside