Windsor EPB2, Руководство пользователя

Страница: 6 / 12

To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com
6
CHASSIS ASSEMBLY
1
1
9
6
7
98255 9/15/97
Ref Qty. Part No. Description Serial No. Notes:
From To
1 41236 Hubcap, 5/8” shaft
2 89114 Wheel, 10” dia. 544841 –
3 70088 Screw, 10–32 x 1/2 PHMS
4 87016 Washer, #10 Star
5 57047 Nut, 1/4–20 Lock
6 57039 Nut, 1.5 NPT Flange
7 70020 Screw, 1/4–20 x 1/2 HHMS
8 87025 Washer, 1/4 Star
9 87013 Washer, 1/4 ID x 5/8 OD
10A 39028 Hose, 3/8 rubber x 13”
10B 39178 Hose, 3/8 rubber X 21.5 (Japan)
11 20042 Clamp, 3/8 Hose (D–slot)
12 40014 Hosebarb, 1/4MPT x 3/8
13 73239 Spacer, Valve
14 84003 Valve, 115V LP 2–Way Solenoind
15 50267 Label, Raise/Lower Brush
16 OPEN
17 62130 Plate, Pump
18 57081 Nut, 10–32 Captive J
19 65129 Pump, 115V 100 PSI w/Adv.
20 40033 Hosebarb, 1/4 MPT X 3/8 90D
21 40014 Hosebarb, 1/4 MPT X 3/8
22 70066 Screw, 10–32 x x 3/4 PHMS
23 54077 Muffler, Vac Exhaust
BELT ADJUSTMENT
1. When servicing brush motor or brush assembly always check
belt for proper tension. The belt should be taut to prevent it
from slipping on cogged pulleys . To tighten belt, loosen motor
mounting nuts and rotate motor rearward just enough to tighten
belt.
VAC MOTOR EXHAUST FILTER
1. Remove (2) bolts holding chassis to tank.
2. Tilt machine back to rest on handle.
3. Remove hex nut from PVC muffler.
Repair or replace as needed.
POWER HEAD LIFT CABLE
1. Remove recovery tank/vac motor assembly.
2. Tilt machine back to rest on handle. Remove bolt holding cable
to lift bracket and (2) power head pivot bolts.
3. Remove guide pulley bracket assembly and remove from pulley.
4. Remove pedal and bracket assembly (4) screws. Replace cable as
required. Reinstall pedal assembly and power head assembly. To
adjust cable: Depress cable so that power head almost touches
vac shoe housing. Raise and lower power head with pedals to
make sure that the head will “Lock” in UP position when pedal
is depressed.
SOLENOID VALVE
If the machine continues to drip solution from the manifold after pump is
switched off check for: (A) Alkaline buildup in solution lines (B) Lint
or debris lodged in the solenoid valve.
1. Remove (2) Tank mounting bolts from chassis panel. Remove
recovery tank/vac motor assembly.
2. Remove left wheel to access valve retaining screws.
3. Remove in line solenoid valve:
Clean, repair or replace as required.
NOTE: The solenoid valve can be disassembled for cleaning when posi-
tive shut–off is interrupted and valve leaks through tee jets.
4. Remove hex nut at top of valve and lift off coil assembly.
5. Use spanner wrench or small punch and hammer to remove
plunger body. Remove lint and soap residue from plunger.
CAUTION:
When reinstalling valve make sure arrow is pointed in
the direction of solution flow.
11
1