background image

24

Maintenance

Checking Battery Specific Gravity

Use a hydrometer to check the battery specific gravity.

CHECKING GRAVITY

a.

Hydrometer

b.

Battery

NOTE: Do not take readings immediately after adding 
distilled water, if the water and acid are not 
thoroughly mixed, the reading may not be accurate.

Check the hydrometer readings against this chart.

NOTE: If the readings are taken when the battery 
electrolyte is any temperature other than 80°F (27°C), 
the reading must be temperature corrected.

To find the corrected specific gravity reading when the 
temperature of the battery electrolyte is other than 80°F 
(27°): Add (+) to the specific gravity reading 0.004 (4 
points), for each 10°F (6°C) above 80° (27°C).  

Subtract (-) from the specific reading 0.004 (4 points), 
for each 10°F (6°C) below 80°F (27°C).

To Charge The Batteries

When servicing machine, avoid contact with 
battery acid.

Lors de l'entretien de la machine, évitez tout 
contact avec l'acide de batterie.

Batteries emit hydrogen gas.  Explosion or fire can 
result.  Keep sparks and open flame away.  Keep 
covers open when charging.

Les batteries émettent du gaz hydrogène. Une 
explosion ou un incendie peut en résulter. 
Maintenez les étincelles et les flammes nues à 
l’écart. Gardez les carters ouverts lors du charge-
ment.

Wear eye protection and protective clothing when 
working with batteries.

Portez des lunettes de protection et des vêtements 
de protection lorsque vous travaillez avec des 
batteries.

Charge batteries in a well ventilated area.  Leave 
the battery cover open.

Chargez les batteries dans un endroit bien ventilé.  
Gardez les carters ouverts lors du chargement.

Use a 36 volt, 18 amp maximum output or 25 amp 
(depending on the size of the batteries), DC charger 
which will automatically shut off when the batteries are 
fully charged.

1.

Stop the machine in a clean, well ventilated area 
next to the charger.  

2.

Turn "OFF" machine.

FOR SAFETY: Before leaving or servicing 
machine; stop on level surface, turn off machine 
and remove key.

3.

Raise the battery cover

SPECIFIC GRAVITY @ 

80

°

F (27

°

C)

BATTERY CONDITION

1.265

100% CHARGED

1.225

75% CHARGED

1.190

50% CHARGED

1.155

25% CHARGED

1.120

DISCHARGED

86400280 Operators Manual - Cutter 36V Standard

Содержание BSCSC326




































Отзывы: