Winco HPS6000HE/I страница 17 Скачать руководство пользователя

Страница: 17 / 20

60706-238/H

G. Clean the dirt from the inside of the air cleaner body

and cover. Reinstall the air filter in housing making sure

the packing is in place beneath the filter element.

Tighten the wing nut securely.

H. Install and secure the cover.

SPARK PLUG

Replace annually or every 300 hours of operation. Always

replace with the same spark plug that came in the engine

and check gap before installing. Spark plug gap is 0.030”.

Poor spark will also occur if spark plug wire does not fit

firmly on spark plug. If this happens, reform the terminal to

fit firmly on spark plug tip.

CARBON CANISTER

Designed to collect, store, and dispose of fuel vapors

created in the fuel tank/fuel system. The canister should last

the life of the unit as long as it stays dry.

Содержание HPS6000HE/I





















Результаты поиска

Содержание HPS6000HE/I

Отзывы:

Похожие инструкции для HPS6000HE/I

Бренды по названию

Популярные бренды

Winco HPS6000HE/I, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HPS6000HE/I

Отзывы:

Похожие инструкции для HPS6000HE/I

Бренды по названию

Популярные бренды