background image

 

© by WilTec Wildanger Technik GmbH  

Item 61811 

Page 2 

 

http://www.WilTec.de

 

http://www.aoyue.eu 

  

11 2021

-1

 

http://www.teichtip.de

 

 
The information contained in this document may alter at any time without previous notice. It is prohibited 
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served. 
The  WilTec  Wildanger  Technik  GmbH  cannot  be  held  accountable  for  any  possible  mistakes  in  this 
operating manual, nor in the diagrams and figures shown. 
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure 
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided. 
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing 
from you. 
 
Send an e-mail to: 
 

[email protected]

 

 
or use our contact form: 
 

https://www.wiltec.de/contacts/

 

 
The most recent version of this manual in various languages can be found in our online shop via: 
 

https://www.wiltec.de/docsearch

 

 
 
Our postal address is: 
 
WilTec Wildanger Technik GmbH 
Königsbenden 12 
52249 Eschweiler 
Germany 
 
Do you wish to pick goods up? Our pick-up address is: 
 
WilTec Wildanger Technik GmbH 
Königsbenden 28 
52249 Eschweiler 
Germany 
 
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or 
placing your order via the webshop. 
 
E-mail: [email protected] 
Tel:+49 2403 55592-0 
Fax: +49 2403 55592-15 
 
To return orders for exchange, repair or for other purposes, please use the following address. Attention! 
To  allow  for  a  smooth  execution  of  your  complaint  or  return,  it  is  important  to  contact  our  customer 
service team before returning the goods. 
 
Returns Department 
WilTec Wildanger Technik GmbH 
Königsbenden 28 
52249 Eschweiler 
 
E-mail: 

[email protected]

 

Tel:+49 2403 55592-0 
Fax: +49 2403 55592-15 
 

 

Содержание 61811












Отзывы: