WilTec 50752 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 9

WilTec 50752 Скачать руководство пользователя страница 7

© by WilTec Wildanger Technik GmbH

Seite 7

http://www.wiltec.info

Function:

1.

Starts and Stops the pump automatically.

2.

It protects the pump against damage caused by dry running.

3.

The pressure switch starts the pump for 15 seconds, if it is connected to the voltage
source. If the pressure in the line system drops, the pump is restarted. In the case of the
conventional systems with pressure switch & pressure tank, the pump stops running if a
certain pressure level is achieved. In contrast to this, the pressure switch stops depending
on the flow rate. In doing so it d

elays the pump’s switching off for a few seconds (7 to 15

seconds) to minimize the number of pump starts.

LED-indication:

1. The upper (1st) LED (Alarm) blinks: the automatic unit is off due to lack of water (protection

against dry running), press

„Restart“ to start the unit again.

2.  The middle (2nd) LED blinks: the pump is switched on.
3.  The lower (3rd) LED blinks: the switch has voltage
4.  Restart (Reset)

– restart button

Possible dysfunctions and their solutions:

Dysfunction

Dysfunction of the unit

Dysfunction outside the unit

The pump won’t start

-

Circuit board is damaged

-

Missing voltage

-

Pump is defect

-

Mixed up electric cables

Dry running display
despite water

-

Set pressure too high (Adjust the
pressure setting screw till the red
Alarm-LED is off, if the pump stops

Pump does not stop

-

Circuit board is damaged

-

The flow detector is trapped in the
upper position

-

the reset-button is blocked

-

The pump has not enough pressure

-

There is a leak with more
than 0,6 l/min loss

Pump runs intermittently
(The pump starts and
stops constantly)

-

Circuit board is damaged

-

The pump has not sufficient
pressure

-

There is a leak with more
than 0,6 l/min loss

«
...
5
6
7
8
9
»

Содержание 50752










Отзывы:

Нет отзывов