background image

English

Installation and maintenance instructions Wilo-Horizontal pumps 

NP

G

they are subject to a +3 dB tolerance, and cannot 
be guaranteed.
The values are based on the noisiest ungeared 
electric motors which are likely to be encountered. 
They represent Sound Pressure Levels at 1 m 
(3.3 ft) from the directly driven pump, for "free 
field over a reflecting plane".

If a pump only has been purchased, for fitting with 
your own driver, then the "pump only" noise levels 
from the table should be combined with the level 
for the driver obtained from the supplier. If the 
motor is driven by an inverter, it may show an 
increase in noise level at some speeds. Consult a 
Noise Specialist for the combined calculation.   

In areas where the staff has to intervene, remem-
ber that when the level of the sound pressure is:

Below 70 dBA:

It is not necessary to take special precautions.

Above 70 dBA:

People working continuously in the machine room 
must be supplied with protective devices against 
noise.

Below 85 dBA :

No particular measures need to be taken for casual 
visitors staying in the room during a limited period.

Above 85 dBA:

The room must be considered as a dangerous area 
because of the noise and a warning sign must be 
fixed at each entry warning the people coming 
into the room, even for a short period, that they 
must wear hearing protection.

Above 105 dBA:

Special hearing protection adapted to this noise 

level and to the spectral noise components must 
be installed and a warning sign to this effect erec-
ted at each entry. The staff in the room must    
wear ear protection.
Make sure that the noise, which travels through 
the walls and windows, does not generate too 
high noise levels in the machine room's surroun-
dings.

2 Transport and storage

2.1

Consignment receipt and unpacking

Immediately after receipt of the equipment it 
must be checked against the delivery and shipping 
documents for its completeness and that there 
has been no damage in transportation.
Any shortage and or damage must be reported 
immediately and received in writing within one 
month of receipt of the equipment. Later claims 
cannot be accepted.
Check any crate, boxes and wrappings for any 
accessories or spare parts that may be packed 
separately with the equipment or attached to 

Typical sound pressure level, 
dBA, L

pA

 at 1 m reference 20

P

Pa 

(L

wA

 sound power1 pW where L

pA

  > 85 dBA)

Motor size and speed

3550 r/min

2900 r/min

1750 r/min

1450 r/min

Pump and 

motor

Pump 

only

Pump and 

motor

Pump 

only

Pump and 

motor

Pump 

only

Pump and 

motor

Pump 

only

kW (hp)

dBA

dBA

dBA

dBA

dBA

dBA

dBA

dBA

<0.55 (<0.75)

71

66

64

62

64

62

63

62

0.75  (1)

74

66

67

62

67

62

63

62

1.1 (1.5)

74

68

67

64

67

64

65

64

1.5 (2)

77

70

70

66

70

66

66

66

2.2 (3)

78

72

71

68

71

68

68

68

3 (4)

81

74

74

70

74

70

70

70

4 (5)

82

75

75

71

75

71

71

71

5.5 (7.5)

90 (99)

77

83

73

76

73

72

71

7.5 (10)

90 (99)

78

83

74

77

74

73

72

11 (15)

91 (100)

80

84 

76

78

76

74

73

15 (20)

92 (101)

83

85 (94)

79

80

79

76

75

18.5 (25)

92 (101)

83

85 (94)

79

80

79

76

75

22 (30)

92 (101)

83

85 (94)

79

81

79

77

75

30 (40)

100 (109)

85 (94)

93 (102)

81

84

80

80

76

37 (50)

100 (109)

86 (95)

93 (102)

82

84

80

80

76

45 (60)

100 (109)

87 (96)

93 (102)

83

84

80

80

76

55 (75)

100 (109)

88 (97)

95 (104)

84

86 (95)

81

82

77

75 (100)

100 (109)

90 (99)

95 (104)

86 (95)

88 (97)

81

83

78

90 (120)

100 (109)

90 (99)

95 (104)

86 (95)

90 (99)

81

85 (94)

78

110 (150)

100 (109)

91 (100)

95 (104)

87 (96)

91 (100)

83

86 (95)

79

150 (200)

101 (110)

92 (101)

96 (105)

88 (97)

91 (100)

83

86 (95)

79

Содержание NPG 100-315





























Отзывы: