Wilo 4/5 TYPE 17, Инструкция по установке и эксплуатации

Страница: 15 / 42

Installation and operating instructions WILO Mather and Platt – Sump Pumps 15
•
Depending on the type, size and capacity (kW), the products
produce a sound pressure up to 75 dB (A) to 110 dB (A).
•
The actual sound pressure, however, depends on several
factors. These include, for example, type of prime mover,
installation type; fastening of accessories and pipeline,
operating site condition, background noise, etc.
•
Once the product has been installed, we recommend that the
operator makes additional measurements under all operating
conditions.
2.5 Safety instructions for installation and
maintenance work
The operator must ensure that all installation and maintenance
work is carried out by authorized and qualified personnel, who
are sufficiently informed from their own detailed study of the
operating instructions.
Work on the product/unit must only be carried out when at a
standstill. It is mandatory that the procedure described in the
installation and operating instructions for shutting down the
product/unit be complied with.
Immediately on conclusion of the work, all safety and
protective devices must be put back in position and/or
re-commissioned.
2.6 Unauthorized modification and manufacture of
spare parts
Unauthorized modification and manufacture of spare parts will
impair the safety of the product/ personnel and will make void
the manufacturer's declarations regarding safety.
Modifications to the product are only permissible after
consultation with the manufacturer. Original spare parts and
accessories authorized by the manufacturer ensure safety. The
use of other parts will absolve us of liability for consequential
events.
2.7 Improper use
The operating safety of the supplied product only guaranteed
for conventional use in accordance with Section 4 of the
operating instructions. The limit values on any account must
not fall under or exceed those specified in the catalogue/data
sheet.
2.8 Safety & control devices
Direct controls are applicable when the pump is supplied along
with motor/panels. When motor/ panel is in end user’s scope of
supply, it is advised to go for CE approved motors /panels.
Environmental safety:
Disposal of any unwanted/scrap material should be disposed in
appropriate way so as not to cause any harm to the
environment. No hazardous material is used in WILO Mather &
Platt pumps.
NOTE:
To avoid ambiguity in the use of the word
„replace” the words „re p lace” and „renew” are used in this
manual in the following context: Replace - To put back, in
its existing state, a part or component that has previously
been removed. Renew - To substitute a new part of
component
for a worn or damaged one.
3. Transport & Interim storage
Immediately check the pump and transport packaging for
damage in transit upon receipt. Take the necessary steps
within the period defined by the transport company in the
event of damage in transit.
DANGER! Risk of getting crushed!
The installation or removal of the product must not be
performed by one person alone. Measures should be taken
to bar persons from standing beneath a suspended load.
Further- more, it is also prohibited to move suspended
loads over exposed workplaces where people are present.
The fastening devices should be adapted to the conditions
at hand (weather, hooking system, load, etc.) Use suitable
fastening devices to handle the weight of the product.
CAUTION! Risk of damage to the pump!
Risk of damage due to improper handling during transport
and storage.
The pump should be protected against humidity, frost and
mechanical damage during transport and interim storage.
3.1 Handling (Refer Fig. 1; Page No. 3)
CAUTION! Risk of damage to the pump!
Risk of falling!
Pumps should never be lifted with motor mounted on motor
stool. Lifting lugs provided on motor stool are to be used
only for lifting the pump during maintenance. Pump to be
lifted /inserted in part by part. Safe working load of wire
ropes reduces with increase in included angle. Never put
down or pick up the product when it is not secured. Tilting
of the product should be avoided at all costs.
Only suitable lifting gear and load carrying equipment with
valid test certificates and adequate lifting capacity for the
loads involved (such as belts/ wire ropes/slings) should be
used for lifting & transporting the product.
If chains are used, they should be secured against slipping
along with protective cover to prevent damage to the
product, paint and/or injury to personnel. When lifting, care
to be taken so that pump flanges, shaft extensions etc. are
not damaged.
To lift the pump see lifting diagrams - see also general
safety Information, point 2 Page No. 14) these must have
sufficient load bearing capacity to ensure that the product
can be transported safely.