Wildix W-AIR 70 Скачать руководство пользователя

Страница: 13 / 16

Technical Notes

Handover functions

To make it possible for the cordless phone to move between the gateways without dropping
ongoing calls, good radio coverage between the adjacent gateways is required.

DND, Call Forward and other settings

You can set them by dialing feature codes of WMS, the status is notified in real time on the
device.

Upgrade Procedure of W-AIR

Requirements

WMS version 2.12.20859.1 or higher

Upgrade procedure

Base stations

Upgrade should be done, if the current FW version is less than

2.42 for WMS2.0

2.90 for

WMS3.0

• Go to WMS

→

Devices

→

select all the base stations to be upgraded

→

press

“Configure / Sync device” and wait for several minutes. After the reboot of the base station
the new version appears on the WMS devices page

W-AIR Administrator’s Manual

Содержание W-AIR 70

















Результаты поиска

Содержание W-AIR 70

Отзывы:

Похожие инструкции для W-AIR 70

Бренды по названию

Популярные бренды

Wildix W-AIR 70, Руководство администратора

Результаты поиска

Содержание W-AIR 70

Отзывы:

Похожие инструкции для W-AIR 70

Бренды по названию

Популярные бренды