manualshive.com logo in svg

Wilden PS8 Saniflo HS Series, Инженерия, эксплуатация и обслуживание

Поделиться
Скачать
Wilden PS8 Saniflo HS Series Скачать руководство пользователя страница 9

WIL-12620-E-03

 

7 

WILDEN PUMP & ENGINEERING, LLC

S e c t i o n   4

P E R F O R M A N C E

Flow rates indicated on chart were determined by pumping water.

For optimum life and performance, pumps should be specified so that daily operation 
parameters will fall in the center of the pump's performance curve.

Flow rates indicated on chart were determined by pumping water.

For optimum life and performance, pumps should be specified so that daily operation 
parameters will fall in the center of the pump's performance curve.

PS8 SANIFLO™ HS

FULL-STROKE PTFE-FITTED

PS8 SANIFLO™ HS

 

FULL-STROKE INTEGRAL 

PISTON DIAPHRAGM-FITTED

Ship Weight ............................49 kg (109 lb)
Air Inlet ....................................19 mm (3/4")
Inlet ............................................ 51 mm (2")
Outlet ......................................... 51 mm (2")
Suction Lift ....................... 3.2 m Dry (10.6')
   

9.0 m Wet (29.5')

Disp. per Stroke

1

 ..................1.0 L (0.27 gal)

Max. Flow Rate ............ 560 lpm (148 gpm)
Max. Size Solids ...........................................
  

Mushroom Valve  6.4 mm (1/4")

   

Ball Valve  12.7 mm (1/2")

Surface Finish .............. Ra 0.8 μm (32 μ-in)

1

Displacement per stroke was calculated at 

4.8 bar (70 psig) air inlet pressure against a 
2 bar (30 psig) head pressure.

Example: To pump 159 lpm (42 gpm) against  a 
discharge head of 4.2 bar (60 psig) requires 5.6 bar 
(80 psig) and 60 Nm

3

/h (35 scfm) air consumption.

Caution: Do not exceed 8.6 bar (125 psig) 
air supply pressure.

Ship Weight ............................49 kg (109 lb)
Air Inlet ....................................19 mm (3/4")
Inlet ............................................ 51 mm (2")
Outlet ......................................... 51 mm (2")
Suction Lift ....................... 3.9 m Dry (12.7')
   

9.0 m Wet (29.5')

Disp. per Stroke

1

 ..................1.0 L (0.27 gal)

Max. Flow Rate ............ 534 lpm (141 gpm)
Max. Size Solids ...........................................
  

Mushroom Valve  6.4 mm (1/4")

   

Ball Valve  12.7 mm (1/2")

Surface Finish .............. Ra 0.8 μm (32 μ-in)

1

Displacement per stroke was calculated at 

4.8 bar (70 psig) air inlet pressure against a 
2 bar (30 psig) head pressure.

Example: 

To pump 246 lpm (65 gpm) against a 

discharge head of 2.8 bar (40 psig) requires 5.60 bar 
(80 psig) and 75 Nm

3

/h (44 scfm) air consumption.

Caution: Do not exceed 8.6 bar (125 psig) 
air supply pressure.

Содержание PS8 Saniflo HS Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды