Wilden PS8 Saniflo HS Series, Инженерия, эксплуатация и обслуживание

Страница: 24 / 40

WILDEN PUMP & ENGINEERING, LLC 22
WIL-12620-E-03
REASSEMBLY:
Upon performing applicable maintenance to the air
distribution system, the pump can now be reassembled.
Please refer to the disassembly instructions for photos
and parts placement. To reassemble the pump, follow
the disassembly instructions in reverse order. The
air distribution system needs to be assembled first,
then the diaphragms and finally the wetted path. The
following tips will assist in the assembly process.
• Lubricate air valve bore, center section shaft and pilot
spool bore with NLGI grade 2 white EP bearing grease
or equivalent.
• Clean the inside of the center section shaft bore to
ensure no damage is done to new shaft seals.
• A small amount of NLGI grade 2 white EP bearing
grease can be applied to the muffler and air valve
gaskets to lubricate gaskets during assembly.
• Make sure that the exhaust port on the muffler plate
is centered between the two exhaust ports on the
center section.
• Stainless-steel bolts should be lubed to reduce the
possibility of seizing during tightening.
• Use a mallet to tap lightly on the large clamp bands
to seat the diaphragm before tightening.
MAXIMUM TORQUE SPECIFICATIONS
Description of Part Max. Torque
Air Valve 13.6 N·m (120 in-lb)
Air Chamber Bolts 27.1 N·m (20 ft-lb)
Outer Pistons, All 54.2 N·m (40 ft-lb)
Center Block-to-Stand Bolt 44.7 N·m (33 ft-lb)
Center Block-to-Bushing Bolt 44.7 N·m (33 ft-lb)
Locking Pin 44.7 N·m (33 ft-lb)
Anti-Rotation Bolt 67.8 N·m (50 ft-lb)
SHAFT SEAL INSTALLATION:
PRE-INSTALLATION
• Once all of the old seals have been removed, the
inside of the bushing should be cleaned to ensure
no debris is left that may cause premature damage
to the new seals.
INSTALLATION
The following tools can be used to aid in the installation
of the new seals:
Needle-Nose Pliers
Phillips Screwdriver
Electrical Tape
• Wrap electrical tape around each leg of the needle-nose
pliers (heat shrink tubing may also be used). This is done
to prevent damaging the inside surface of the new seal.
• With a new seal in hand, place the two legs of the
needle-nose pliers inside the seal ring. (See Figure A.)
• Open the pliers as wide as the seal diameter will allow,
then with two fingers pull down on the top portion of
the seal to form a kidney shape. (See Figure B.)
• Lightly clamp the pliers together to hold the seal into
the kidney shape. Be sure to pull the seal into as tight
of a kidney shape as possible, this will allow the seal to
travel down the bushing bore easier.
• With the seal clamped in the pliers, insert the seal into
the bushing bore and position the bottom of the seal
into the correct groove. Once the bottom of the seal is
seated in the groove, release the clamp pressure on the
pliers. This will allow the seal to partially snap back to its
original shape.
• After the pliers are removed, you will notice a slight
bump in the seal shape. Before the seal can be properly
resized, the bump in the seal should be removed as
much as possible. This can be done with either the
Phillips screwdriver or your finger. With either the side
of the screwdriver or your finger, apply light pressure
to the peak of the bump. This pressure will cause the
bump to be almost completely eliminated.
• Lubricate the edge of the shaft with NLGI grade 2
white EP bearing grease.
• Slowly insert the center shaft with a rotating motion.
This will complete the resizing of the seal.
• Perform these steps for the remaining seals.
Figure A
SHAFT SEAL
TAPE
Figure B
SHAFT SEAL
TAPE
NEEDLE-NOSE
PLIERS
NOTE: To ensure proper
alignment during reas-
sembly of manifold/liquid
chamber interface, turn
off-set portion of valve
housing to the left or to
the right. This procedure
works for the inlet mani-
fold and discharge mani-
fold connections.
Off-Set
Valve
Housing
Twist
R E A S S E M B L Y H I N T S & T I P S