5
Attached Table
:
Program and the Program number
6 colors skip & audio control
5 colors skip & audio control
Function
Pro. No.
PS.1
PS.2
Red
6 colors skip
5 colors skip
6 colors fade
6 colors skip & chase
6 colors fade & chase
Function
Pro. No.
No Light
White
Sky-B
Green
Yellow
Blue
Function
Pro. No.
P.00
P.06
P.01
P.07
P.02
P.08
P.03
P.09
P.04
P.1 0
P.05
P.1 1
Fig.5
RC-15
Wireless Remote Controller
3
6
9
2
5
8
0
SP
DIM
PRO
1
4
7
4. Wireless
remote controller (See Fig.5):
Press the two buttons “
UP
” / “
DOWN
” besides the Display at the same time. When it
displays , press either button of “
UP
” / “
DOWN
” to show “
”
(status of remote control). The remote function is on.
15-Key Remote Controller:
(1) Program Selection: Press“
PRO
”, then press the digit key on the
controller, “
00
”-“
13
”, to choose the desirable program, or you can
use “ ”,“ ” to select.
(2) Dimming: Press the key “
DIM
”, then press “
0
”-“
7
” to have the
desirable brightness, or you can use “ ”,“ ” to adjust.
(3) Speed of the twinkle wheel
:
Press the key “
SP
”, then press “
0
”-“
7
”
to adjust the speed, or you can use “ ”,“ ” to adjust.
“
”
or “
”
Notice:
①
Address
code of slave (machines) are not adjustable under remote control status.
②
When you are selecting the program, only double-digit numbers on the controller
are recognizable (e.g. 00, 01, 02...).
6
3. Commonly used installation method of fiber optic cable:
(1) Side Lighting Fiber Optic:(See Fig.3).
2.Installation of the end part of the Multi-String fiber optic:
(1) Drill holes on the installing board according to the design. Then insert the fiber optic
(2) Insert the finished Fiber Connector into the Fixing Flange and screw tightly the Screw.
string into holes and fix it with epoxy glue. Trim the end of the fiber string to be flush
with the board or at a required length. Fasten the other end of the fiber string to a
harness and insert the harness into PG Connector and Fiber Connector. Apply the
hot knife to cut fiber end flush with the Fiber Connector.
(See Fig.2).
1. Connecting the fiber optic with Light Engine:
Solid Core fiber optic(See Fig. 1):
(1) Cut the fiber to the specified length. The cross section should be vertical to the
fiber and keep clean and smooth.
(2) Peel off 50-100mm of the PVC jacket of the fiber optic cable (not necessary if
there is no PVC jacket). Be careful not to hurt the fiber optic.
(3) Unscrew the
PG
Connector and insert the fiber optic cable into the
PG
Connector
and Fiber Connector until the end of the cable is flush with the Fiber Connector.
Screw tightly the PG Connector.
(4) Insert the finished Fiber Connector into the Fixing Flange, screw tightly the Screw.
Single Lighting
End Plug
Light
Engine
Side
Glow
Fiber
Optic
Single Set
Double
Lighting
Multi Sets
Double
Lighting
Fig.3
(2) End Lighting Fiber Optic:
(See Fig.4).
With End Piece
Fig.4
Fiber
Optic
PG
Connector
Front Case
Fiber
Connector
Fixing Flange
Fig. 1
Fig. 2
Chapter
3 Installation of Fiber Optic
