background image

 

YOUR FIRE 

 

UNPACKING, ELECTRICAL INSTALLATION  

& GENERAL SAFETY 

 

GENERAL: 

Unpack  the  fire  carefully  and  retain  the  packaging  for  possible  future  use,  for 
example in the event of moving or returning the fire to your supplier. Remove any 
plastic protection film and transit tape.  
The fire incorporates a flame effect that may be enjoyed at any time of the year; 
using the flame effect on its own only requires minimal electricity.  

 

THIS APPLIANCE MUST BE EARTHED 

 

Check that the voltage shown on the rating label of your fire is the same as your 
dwelling electricity supply which must be AC (alternating current). 
The mains  cord  of  the fire  has  a  UK  type  plug fitted with  a  13amp fuse;  when 
replacing  a fuse  use  a  13amp fuse  approved  to  BS  1362.  The fuse  cover  of  a 
moulded on plug must be refitted after changing the fuse. Should the fuse cover 
become lost, the plug must not be used until the correct replacement fuse cover 
is obtained from your service agent. 
The wires in the mains supply cord are coloured in accordance with the following 
code: Green and Yellow = Earth,   Blue = Neutral,   Brown = Live. 
If  your  fire  is  fitted  with  a  moulded  on  mains  plug  which  is  not  suitable  for  the 
socket outlets in your dwelling, the plug must be cut off and an appropriate one 
fitted.  
Note: A plug cut off from a flexible cord presents a shock hazard if inserted in a 
13  amp  socket  elsewhere  in  the  dwelling,  to  avoid  this  remove  the  fuse  and 
dispose of immediately. 
If  you  are fitting  an  alternative  type  of  plug then  the  colours  of the  wires  in  the 
mains  cord  may  not  correspond  with  the  identifying  markings  on  the  plug 
terminals. In this case proceed as follows: 
The  wire  which  is  coloured  Green/Yellow  must  be connected  to  the terminal  in 
the  plug  which  is  marked  by  the  letter  E  or  by  the  earth  symbol  or  coloured 
Green or Green/Yellow. The wire which is coloured Blue must be connected to 
the terminal in the plug which is marked by the letter N or coloured Black. The 
wire  which  is  coloured  Brown  must  be  connected  to  the  terminal  in  the  plug 
which is marked by the letter L or coloured Red. 

 

Содержание Fuego LE Timer fires

















Отзывы: