background image

2

Chapter  MXT Pro Controls

(Dual Control) in Coin & Jewelry or 
Relic -

 While operating in the Coin & Jewelry or Relic 

MODES the Dual control operates as a DISC (discrimina-

tion) control. DISC (Discrimination) is used to adjust the level 

of audio rejection against trash metals. 

The “Triangle” just below NICKEL is recommended for most 

general purpose searching. In this position, the detector 

will provide a reject response to most iron and light foil and 

respond to most valuables including jewelry.  

Positions lower than “triangle” (counterclockwise) will provide 

less trash metal rejection, to the point of detecting virtually 

all types of common metals. 

Positions higher than the “triangle” (clockwise) will reject 

more trash metals including aluminum pull-tabs. The display 

will continue to indicate I.D. even though the audio discrimi-

nator will signal with a reject (suppressed or broken) sound.  

Nickels and some jewelry will also be rejected with DISC 

settings much greater than the “triangle”. 

The “triangle” position is recommended for most MODES.  

If when searching at the “triangle” position you feel you are 

digging too much trash, adjust DISC slightly clockwise and 

try again. Using the lowest (furthest counterclockwise) posi-

tion that is practical considering the common trash metals 

in your area is important in order to find items of jewelry.  

Settings that suppress the USA nickel, and/or a medium 14K 

gold ring, will also suppress most other gold jewelry.  For 

jewelry, it is best to keep the Discrimination at or near the 

“triangle” and rely on the display and depth indication to sort 

out aluminum.

Dual Control in Prospecting - 

When in the Prospecting MODE, the DUAL CONTROL is 

used to adjust the level or speed of SAT (Self Adjusting 

Threshold).  

The Threshold or continuous faint hum heard during opera-

tion of the MXT Pro can increase or fade due to environmen-

                       DUAL CONTROL

DISC- DISCRIMINATION (outer ring)

When in COIN & JEWELRY and RELIC MODE

VARIABLE SELF ADJUSTING THRESHOLD SPEED (SAT)

When in Prospecting MODE

Содержание MXT PRO









































Отзывы: