Whiteley Electronics PETS-2 Скачать руководство пользователя страница 8

Страница: 8 / 40

Page

8 of 40

Issue 2

13/12/99

PETS-2 Crossing Telephone System

QUICKFIX INSTALLATION HANDBOOK

1 off PETS 2 Signal Box unit, with card removal ‘pullers’ (inside)

1 off Junction Box, complete with pre-wired connectorised leads.

1 off Installation Handbook (this book)

1 off 9 pin female ‘D’ connector (for the power supply lead)

1 off Earth lead - M6 ring terminal and 2 metre green/ yellow wire

2.2

Level Crossing Kit (WEL part A35155)

Upon opening the packaging, the contents should be checked to the following list:

1 off PETS 2 Level Crossing unit, with card removal ‘pullers’ (inside)

1 off Junction Box, complete with pre-wired connectorised leads.

1 off Installation Handbook (this book)

1 off 9 pin female ‘D’ connector (for the power supply lead)

1 off Earth lead - M6 ring terminal and 2 metre green/ yellow wire

3. ACCESSORIES

The following table provides information on the standard accessories available for use with
PETS 2:

WEL Part No.

Signal Box

Crossing

Description

A33838

Note 2

Line Card - for local telephones. This Line card
is identical to the original PETS Line card; and
is also used on PETS 2 but within the Level
Crossing unit only.

A35173

Note 1

Line Card - Signalbox PETS2. This item is
different to the original due to a modified CALL
button arrangement.

A34566 (new
version from Q3
’98 - A35168)

Note 3

Power supply and battery charger, batteries
not included.

A35166

Note 4

Remote Alarm Display Kit

A35169

Note 5

Battery Set (4 off) 6Ahr

A35170

Note 5

Battery Set (4 off) 12Ahr

A35171

Note 6

Battery Set (4 off) 17Ahr

A35172

Note 7

Firmware Upgrade (when applicable)

G42279

Note 8

‘Handbook

for

Design,

Installation

and

Maintenance’

G42279CD

Note

CD version of ‘Handbook for Design,

Содержание PETS-2









































Результаты поиска

Содержание PETS-2

Отзывы:

Похожие инструкции для PETS-2

Бренды по названию

Популярные бренды

Whiteley Electronics PETS-2, Быстрое руководство по установке

Результаты поиска

Содержание PETS-2

Отзывы:

Похожие инструкции для PETS-2

Бренды по названию

Популярные бренды