Whiteley Electronics PETS-2 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 40

background image

PETS-2 Crossing Telephone System

QUICKFIX INSTALLATION HANDBOOK

Page 19

of 40

Issue 2

13/12/99

19

5. INSTALLATION

The instructions given in this section will assume that the installation is of the most common
type; a single AHB crossing with just one telephone either side of the line, and a single
PETS Signal Box Unit, manually controlled. It is assumed that the installation has been
surveyed by a competent and trained technician, and that the installer has been given any
additional or contrary instructions along with the equipment and this manual.

Before attending site produce the paper labels for insertion within the windows of the
Signalbox Unit. To receive the latest version of the label pro-forma in WORD 6 format, send
an e-mail request to :

[email protected]

[please give your name and company - we will also send

update bulletins by return]

5.1 Installation tools

The following tools will be required:
1. Montdragon (formerly ADC) QDF IDC tool.
2. 10mm ring spanner
3. 2mm Allen Key
4. Soldering Iron (15watt fine tip, recommended), and self fluxed solder.
5. Screwdrivers, flat blade various sizes.
6. Scissors (for labels)
7. Wire cutters
8. Pen knife

5.2 Unpacking the equipment

Check the external packing labels before proceeding to distinguish the Signal Box Unit from
the Level Crossing Unit. Use a small pen knife to open the carton sealing tape, do not cut
into the carton more than 5mm, to avoid damage to the equipment within. Remove the
contents.

The packing carton is made of cardboard and may be re-cycled.

5.3 Preparation

Decide where the unit is to be installed, normally this will be onto a wall. The Signal Box
Unit must be installed in a clean and dry location, away from windows that may be left open,
and away from sources of steam or condensation. From the Junction Box, 2 metre cables
with connectors at the ends are to be mated with the PETS unit, into the left hand side
connector plate. The cables are normally kept in place within trunking or by cable clips.

5.4 Wall fixing

It is necessary to disassemble the PETS 2 unit, the procedure is identical for Signal Box
and for the Level Crossing Units:

«
...
17
18
19
20
21
...
»

Содержание PETS-2









































Отзывы:

Нет отзывов

Похожие инструкции для PETS-2

Бренд: GE Страницы: 36

Бренд: Panasonic Страницы: 24

Бренд: EasyPro Страницы: 8

Бренд: M-Audio Страницы: 12

Бренд: Opus Technologies Страницы: 24

Бренд: Panasonic Страницы: 16

Бренд: Saab Страницы: 24

Бренд: Getek Страницы: 6

MemoryPlus 309dp

Бренд: Doro Страницы: 38

Бренд: Uniden Страницы: 64

Memory Phone 9825

Бренд: Interquartz Страницы: 16

Бренд: Oricom Страницы: 24

Бренд: Aiwa Страницы: 76

Бренд: Coby Страницы: 1

Бренд: Furuno Страницы: 67

Бренд: Aiwa Страницы: 80

Бренд: TIE Страницы: 28

Бренд: AGFEO Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды