White Mini-Seis III Pro страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 49

background image

Mini-Seis III Pro™ Operating Manual

Page 6

A Word Concerning This Manual

The content of this manual references the most recent Pro firmware. Instruments with older
firmware versions may not conform to the content. White recommends that the Pro firmware
be kept current. The current version of Seismograph Data Analysis will contain the most
recent Pro firmware. Some earlier versions of Seismograph Data Analysis do not support the
Mini-Seis III Pro. The trade names Mini-Seis III Pro, Mini-Seis III, Mini-Seis and Seismograph
Data Analysis are the property of White Industrial Seismology, Inc.

Introduction

The Mini-Seis III Pro is an enhanced version of the Mini-Seis III and is designed to replace
the Mini-Seis III. It features a 32 bit processor and 16 bit A/D. The Pro has over 3.5GB of
memory and can store many hours or days of continuous waveform data and many months if
not years of continuous histogram data. It may be possible to use the seismograph for many
years without having to erase the memory. Ruggedness, reliability, accuracy and power
conservation are built in to the design. Data transfer by both serial and high speed USB is
supported.

The Pro supports the standard 4 channel configuration, an optional 8 channel configuration
and a high speed single channel mode.

Use

The Pro is designed for many types of vibration monitoring including:



Blast Vibration



Environmental



Construction



Demolition



Underwater



And more…

It can also work with non-standard sensors like hydrophones, dynamic strain gauges and tilt
gauges. The Seismograph Data Analysis V13 and later software was designed for use with
the Pro with both standard and non-standard records.

Operating Modes



Waveform – The standard selection for time history vibration monitoring with trigger
thresholds and a fixed record duration.



Histogram – Primarily used for monitoring continuous or semi-continuous vibration.
The measured data includes the peak levels in each sample interval, the frequency at
the peaks and optionally the vector sum.



Histogram/Waveform – Merges both Waveform and Histogram modes so that
waveform events can be recorded simultaneously with histogram data based on user
specified trigger thresholds.

«
...
4
5
6
7
8
...
»

Содержание Mini-Seis III Pro


















































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Seis III Pro

LM-OG-P2 Advanced

Бренд: Badger Meter Страницы: 48

Бренд: Badger Meter Страницы: 24

Бренд: Bahco Страницы: 92

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: Saimo Страницы: 101

Бренд: OBDPROG Страницы: 8

Бренд: P3 International Страницы: 1

Бренд: DAKOTA ULTRASONICS Страницы: 50

Бренд: Jamar Страницы: 4

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Oldham Страницы: 96

Бренд: LOVATO ELECTRIC Страницы: 10

Бренд: e-sylife Страницы: 2

Бренд: Parker Страницы: 16

Бренд: Waterproof Страницы: 51

3501B1260KG/M010LN

Бренд: PCB Piezotronics Страницы: 10

Бренд: MFJ Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды